Hunter X-CORE

Other manuals for Hunter X-CORE

Questions and Answers:

E
Edwin RamirezSep 17, 2025
Why does my Hunter X-CORE Controller display show dashes in the Solar Sync Settings position?
- G
  gina58Sep 18, 2025
  If the Hunter Controller display shows dashes when the dial is in the Solar Sync Settings position, it could be because: * The Solar Sync sensor is not connected to the controller * The Solar Sync sensor wires may have a break in them or a bad connection Connect the Solar Sync to the “SEN” positions on the wiring terminal. The display will then show the Region and Water Adjustment setting.
J
jasonmorenoAug 25, 2025
Why is my Hunter Irrigation System continuously watering?
- E
  Emily WilsonAug 25, 2025
  If your Hunter Irrigation System controller is continuously watering, it's likely due to having programmed too many start times. Only one start time is necessary to activate a program. To fix this, refer to the section on Setting the Program Start Times to reduce the number of start times.
B
brooke31Aug 25, 2025
What to do if my Hunter Controller display shows “ERR” with a number?
- S
  Stacy WilliamsAug 26, 2025
  If your Hunter Controller display shows “ERR” with a number (1 to 8), it indicates a short in the valve wiring circuit or a faulty solenoid on the station number indicated. Check the wire circuit or solenoid for the valve number indicated. Repair the short or replace the solenoid. Press any button to clear the “ERR” from the display.
D
Daniel SchroederAug 26, 2025
What to do if my Hunter Controller display shows “P ERR”?
- K
  kenneth16Aug 27, 2025
  If the Hunter Controller display shows “P ERR”, it could be due to: * Faulty pump relay or master valve wiring * Incompatible or defective relay or solenoid * Undersized wire to the pump relay or master valve Check the wiring to the relay or master valve solenoid. Press any button to clear the “P ERR” from the display. Check the electrical specification for the pump relay, ensuring you do not exceed the controller's electrical rating, and replace if defective. Replace the wire with a larger gauge wire.
M
Michelle McgeeSep 18, 2025
Why is there no display on my Hunter Controller?
- C
  Carl PageSep 18, 2025
  If there is no display on your Hunter Controller, check the AC power wiring and correct any errors.
C
Christine WarrenSep 23, 2025
What does it mean when a station is running but the icons are flashing on my Hunter X-CORE?
- J
  jonesjoshuaSep 23, 2025
  If your Hunter Controller display shows a station is running but the icons are flashing, it means that the sensor is interrupting irrigation, but the station has been programmed to override the sensor. Check the sensor override status.
B
Bonnie SullivanSep 9, 2025
Why does my Hunter Controller show dashes in the Solar Sync Settings?
- D
  Danielle WalkerSep 9, 2025
  If the Hunter Controller display shows dashes when the dial is in the Solar Sync Settings position, it means that the Solar Sync sensor isn't connected to the controller, or the sensor wires may have a break or bad connection. Connect the Solar Sync to the 'SEN' positions on the wiring terminal. The display will then show the Region and Water Adjustment setting.
M
molly28Sep 10, 2025
How to fix a Hunter X-CORE with no display?
- S
  Shaun LandrySep 10, 2025
  If the display on your Hunter Controller is blank, check the AC power wiring and correct any errors.
J
Joy GomezSep 3, 2025
What does it mean when my Hunter X-CORE display reads “Of,f ”?
- M
  Marc PowellSep 3, 2025
  If the Hunter Controller display reads “Of,f ”, it means that the rain sensor is interrupting irrigation or the sensor jumper has been removed. Slide the rain sensor bypass switch to the BYPASS position to bypass the rain sensor circuit, or reinstall the jumper.
J
John SalazarSep 1, 2025
What does “P ERR” mean on my Hunter Irrigation System display?
- A
  Alexander PriceSep 1, 2025
  If the display on your Hunter Irrigation System shows “P ERR”, there may be a faulty pump relay or master valve wiring, an incompatible or defective relay or solenoid, or undersized wire to the pump relay or master valve. Check the wiring to the relay or master valve solenoid. Also, check the electrical specification for the pump relay, do not exceed the controller's electrical rating, and replace if defective. Consider replacing the wire with a larger gauge wire. Press any button to clear the “P ERR” from the display.

Hunter X-CORE Specifications

General

Start Times Per Program	4
Max Station Run Time	4 hours
Warranty	2 years
Application	Residential
Mounting	Wall mount
Station Timing	1 minute to 4 hours
Number of Stations	2, 4, 6, or 8
Watering Duration	1 minute to 4 hours
Display	LCD
Stations	2, 4, 6 or 8 stations
Indoor/Outdoor	Indoor or Outdoor
Seasonal Adjustment	Yes
Watering Days	7 days
Rain Delay	Yes
Power Source	24V AC transformer
Battery Backup	Yes
Programs	3