Why is my Hunter X-CORE Controller continuously watering?
Your Hunter Controller might be continuously watering because too many start times have been programmed. Only one start time is necessary to activate a program. You can refer to the section on setting the program start times.
What does “P ERR” mean on my Hunter Irrigation System display?
If the display on your Hunter Irrigation System shows “P ERR”, there may be a faulty pump relay or master valve wiring, an incompatible or defective relay or solenoid, or undersized wire to the pump relay or master valve. Check the wiring to the relay or master valve solenoid. Also, check the electrical specification for the pump relay, do not exceed the controller's electrical rating, and replace if defective. Consider replacing the wire with a larger gauge wire. Press any button to clear the “P ERR” from the display.
Why won't my Hunter Irrigation System start automatically?
If your Hunter Irrigation System is not starting automatically at the set start time and is not in the System Off mode, it could be due to several reasons: the AM/PM setting for the time of day or start time is incorrect, the start time is disabled (set to Off), or the controller is not receiving AC power. To solve this, correct the AM/PM of the time of day or start time, check the Setting Program Start Times, and verify the AC power connections.
What to do if Hunter Irrigation System display reads “Of,f ”?
If your Hunter Irrigation System display reads “Of,f,” it means that either the rain sensor is interrupting irrigation or the sensor jumper has been removed. To resolve this, slide the rain sensor bypass switch to the BYPASS position or reinstall the jumper.
What to do if my Hunter Irrigation System display shows “ERR” with a number?
If the display on your Hunter Irrigation System shows “ERR” followed by a number (1 to 8), it means there is a short in the valve wiring circuit, or a faulty solenoid on the station number indicated. Check the wire circuit or solenoid for the valve number indicated. Repair the short or replace the solenoid. Press any button to clear the “ERR” from the display.
Why doesn't my Hunter X-CORE Controller start automatic irrigation at the set time?
If automatic irrigation doesn't start at the set time and the Hunter Controller isn't in the System Off mode, it could be due to several reasons: * Incorrect AM/PM setting for the time of day. * Incorrect AM/PM setting for the start time. * The start time is disabled (set to Off). * The controller isn't receiving AC power. To resolve this, ensure the AM/PM settings for both the time of day and start time are correct. Also, check that the start time is enabled and verify the AC power connections.
What to do if my Hunter X-CORE Controller display shows 'ERR' with a number?
If your Hunter Controller displays 'ERR' followed by a number (1 to 8), it means there's a short in the valve wiring circuit or a faulty solenoid on the indicated station. Check the wire circuit or solenoid for the valve number shown. Repair any shorts or replace the solenoid. After fixing the issue, press any button to clear the 'ERR' message from the display.
What to do if my Hunter Controller display shows “P ERR”?
If the Hunter Controller display shows “P ERR”, it could be due to: * Faulty pump relay or master valve wiring * Incompatible or defective relay or solenoid * Undersized wire to the pump relay or master valve Check the wiring to the relay or master valve solenoid. Press any button to clear the “P ERR” from the display. Check the electrical specification for the pump relay, ensuring you do not exceed the controller's electrical rating, and replace if defective. Replace the wire with a larger gauge wire.
What to do if my Hunter Controller display shows “ERR” with a number?
If your Hunter Controller display shows “ERR” with a number (1 to 8), it indicates a short in the valve wiring circuit or a faulty solenoid on the station number indicated. Check the wire circuit or solenoid for the valve number indicated. Repair the short or replace the solenoid. Press any button to clear the “ERR” from the display.
Why is my Hunter Irrigation System continuously watering?
If your Hunter Irrigation System controller is continuously watering, it's likely due to having programmed too many start times. Only one start time is necessary to activate a program. To fix this, refer to the section on Setting the Program Start Times to reduce the number of start times.
Steps for connecting the Solar Sync sensor to the controller.
Instructions for connecting the Wireless Solar Sync receiver.
Steps to set the current date and time on the controller.
How to set start times for each watering program.
How to set the duration of watering for each station.
Options for selecting watering days (calendar, interval, odd/even).
General| Start Times Per Program | 4 |
|---|---|
| Max Station Run Time | 4 hours |
| Warranty | 2 years |
| Application | Residential |
| Mounting | Wall mount |
| Station Timing | 1 minute to 4 hours |
| Number of Stations | 2, 4, 6, or 8 |
| Watering Duration | 1 minute to 4 hours |
| Display | LCD |
| Stations | 2, 4, 6 or 8 stations |
| Indoor/Outdoor | Indoor or Outdoor |
| Seasonal Adjustment | Yes |
| Watering Days | 7 days |
| Rain Delay | Yes |
| Power Source | 24V AC transformer |
| Battery Backup | Yes |
| Programs | 3 |
To Next Page
