Why does my Husqvarna Lawn Mower say 'Charger cable not connected'?
If your Husqvarna Lawn Mower displays 'Charger cable not connected', it means the charger cable is not connected when changing the PIN code, or when connecting the mower to the loop generator/charger. Connect the charger cable.
Why is my Husqvarna Lawn Mower leaving uneven mowing results?
If your Husqvarna Lawn Mower is mowing unevenly, there are several potential causes. You may need to increase the mowing time if the mower works too few hours per week. The working area might be too large, so consider limiting it or extending the mowing time. Dull blades can also cause uneven mowing, so replace all blades and screws to balance the rotating parts. If the grass is too long relative to the cutting height, increase the cutting height and then successively lower it. Finally, check for grass accumulation by the blade disc or around the motor shaft, ensuring the skid plate and blade disc rotate easily; remove any obstructions if needed.
Why is my Husqvarna AUTOMOWER 210 C not driving?
If your Husqvarna Lawn Mower isn't moving, it may be stuck on something. Free the mower and clear whatever is obstructing it. If wet grass is the issue, wait for the lawn to dry. Consider using Automower® wheel brushes (505 13 27-01) to maintain clean drive wheels and improve traction.
How to fix a blocked wheel motor on Husqvarna AUTOMOWER 210 C?
If the wheel motor on your Husqvarna Lawn Mower is blocked, it's likely that grass or another object has wrapped around the drive wheel. Inspect the drive wheel and remove any obstructions.
Why does my Husqvarna Lawn Mower have no drive?
If your Husqvarna Lawn Mower is not driving, it may be caught on something. Free the mower and rectify the reason for the lack of drive. If wet grass is the cause, wait until the lawn has dried before using the mower.
Why does my Husqvarna AUTOMOWER 210 C Lawn Mower mow for shorter periods than usual?
If your Husqvarna Lawn Mower is mowing for shorter periods than usual, grass or a foreign object might be blocking the blade disc or skid plate. Dismantle and clean these components. This can also be normal in high temperatures (above 25 °C). Finally, the battery could be spent, in which case you should contact your dealer to check and replace it.
What to do if my Husqvarna Lawn Mower goes outside working area?
If your Husqvarna Lawn Mower is displaying 'Outside working area', there are a few possible reasons. The boundary wire might be crossed when connected to the loop generator/charger; if so, switch the two connections. The gradient for the boundary cable could be too steep, so check its routing. Also, the boundary wire might be routed incorrectly around an “island”, so ensure it follows the installation instructions. The boundary wire might be too close to the edge of the working area, so verify its placement. Interference from metallic objects or buried cables could also be the cause; try moving the boundary wire.
Why is my Husqvarna AUTOMOWER 210 C vibrating?
If your Husqvarna Lawn Mower is vibrating, it could be due to an unbalanced blade disc or damaged blades. Inspect the blades and screws and replace them if necessary.
What to do if my Husqvarna Lawn Mower blade disc is blocked?
If the blade disc on your Husqvarna Lawn Mower is blocked, grass or another object has likely become wrapped around it. Check the blade disc and clear away any obstructions.
Why does my Husqvarna AUTOMOWER 210 C Lawn Mower vibrate?
If your Husqvarna Lawn Mower is vibrating, the blade disc might be unbalanced, or the blades could be damaged. Inspect the blades and screws, and replace them if needed.
Crucial safety guidelines for operating the Automower to prevent injury.
Outlines necessary preparations and checks before starting the installation process.
Guides on selecting a location and connecting the loop generator/charger.
Step-by-step instructions for charging the Automower's battery.
Details methods for installing the boundary wire, including stapling and burying.
Instructions for securely connecting the boundary wire to the loop generator.
Procedures to verify the loop signal and ensure the installation is correct.
Process for pairing the Automower with its charging and control station via PIN.
Comprehensive guide on how to safely start the Automower.
Step-by-step guide for safely replacing the mower's cutting blades.
Guide to interpreting fault codes displayed by the Automower's indicator lamps.
Troubleshooting common operational symptoms and their potential causes and actions.
General| Cutting Width | 17 cm |
|---|---|
| Recommended Lawn Area | 600 m² |
| Working area capacity | 600 m² |
| Battery Type | Li-Ion |
| Battery Voltage | 18 V |
| Cutting Height | 20-50 mm |
| Sound level Measured | 58 dB(A) |
| Battery capacity | 2.1 Ah |
| Maximum incline within the working area | 25 % |
| Maximum Slope | 25 % |
| Blade Type | Pivoting razor blades |
| Rain Sensor | Yes |
| Anti-Theft System | PIN code |
| Connectivity | No |
To Next Page
