Hyd-Mech M-16 - Lock-Out Procedure; Lock Out Procedure

Pg 3.1
SECTION 3, SECTION 3,
SECTION 3, SECTION 3,
SECTION 3,
MAINTENMAINTEN
MAINTENMAINTEN
MAINTEN
ANCE AND TROUBLE SHOOANCE AND TROUBLE SHOO
ANCE AND TROUBLE SHOOANCE AND TROUBLE SHOO
ANCE AND TROUBLE SHOO
TINGTING
TINGTING
TING
LL
LL
L
OCK -OUTOCK -OUT
OCK -OUTOCK -OUT
OCK -OUT
Purpose:Purpose:
Purpose:Purpose:
Purpose:
To prevent injury to workers caused by unexpected start-up of machines beingTo prevent injury to workers caused by unexpected start-up of machines being
To prevent injury to workers caused by unexpected start-up of machines beingTo prevent injury to workers caused by unexpected start-up of machines being
To prevent injury to workers caused by unexpected start-up of machines being
worked worked
worked worked
worked on.
OR
Where the starting of a machine or device may endanger the safety of a workerWhere the starting of a machine or device may endanger the safety of a worker
Where the starting of a machine or device may endanger the safety of a workerWhere the starting of a machine or device may endanger the safety of a worker
Where the starting of a machine or device may endanger the safety of a worker
a)a)
a)a)
a)
Control switches or other control mechanisms shall be locked out;Control switches or other control mechanisms shall be locked out;
Control switches or other control mechanisms shall be locked out;Control switches or other control mechanisms shall be locked out;
Control switches or other control mechanisms shall be locked out;
ANDAND
ANDAND
AND
b)b)
b)b)
b)
Other effective precautions necessary to prevent such starting shall be takenOther effective precautions necessary to prevent such starting shall be taken
Other effective precautions necessary to prevent such starting shall be takenOther effective precautions necessary to prevent such starting shall be taken
Other effective precautions necessary to prevent such starting shall be taken
LL
LL
L
OCK OUT PROCEDURE:OCK OUT PROCEDURE:
OCK OUT PROCEDURE:OCK OUT PROCEDURE:
OCK OUT PROCEDURE:
Whenever work is to be performed on a machine, the following steps shall be taken:Whenever work is to be performed on a machine, the following steps shall be taken:
Whenever work is to be performed on a machine, the following steps shall be taken:Whenever work is to be performed on a machine, the following steps shall be taken:
Whenever work is to be performed on a machine, the following steps shall be taken:
1.1.
1.1.
1.
Operator shuts down the machineOperator shuts down the machine
Operator shuts down the machineOperator shuts down the machine
Operator shuts down the machine
2.2.
2.2.
2.
The person in charge should follow Lockout procedures as is required by hisThe person in charge should follow Lockout procedures as is required by his
The person in charge should follow Lockout procedures as is required by hisThe person in charge should follow Lockout procedures as is required by his
The person in charge should follow Lockout procedures as is required by his
organization. The main power disconnect box is supplied with a suitableorganization. The main power disconnect box is supplied with a suitable
organization. The main power disconnect box is supplied with a suitableorganization. The main power disconnect box is supplied with a suitable
organization. The main power disconnect box is supplied with a suitable
mechanism for this purpose as shown below.mechanism for this purpose as shown below.
mechanism for this purpose as shown below.mechanism for this purpose as shown below.
mechanism for this purpose as shown below.
3.3.
3.3.
3.
An attempt to start, is made to check that correct main disconnect is turned off.An attempt to start, is made to check that correct main disconnect is turned off.
An attempt to start, is made to check that correct main disconnect is turned off.An attempt to start, is made to check that correct main disconnect is turned off.
An attempt to start, is made to check that correct main disconnect is turned off.
4.4.
4.4.
4.
The person in charge adds a warning tag to his lock, showing nature of work,The person in charge adds a warning tag to his lock, showing nature of work,
The person in charge adds a warning tag to his lock, showing nature of work,The person in charge adds a warning tag to his lock, showing nature of work,
The person in charge adds a warning tag to his lock, showing nature of work,
date, and workers involved.date, and workers involved.
date, and workers involved.date, and workers involved.
date, and workers involved.
5.5.
5.5.
5.
Each operator working on the machine will place his own safety lock on theEach operator working on the machine will place his own safety lock on the
Each operator working on the machine will place his own safety lock on theEach operator working on the machine will place his own safety lock on the
Each operator working on the machine will place his own safety lock on the
disconnect switch. He keeps his key with him while his lock is in place.disconnect switch. He keeps his key with him while his lock is in place.
disconnect switch. He keeps his key with him while his lock is in place.disconnect switch. He keeps his key with him while his lock is in place.
disconnect switch. He keeps his key with him while his lock is in place.
Each operators lock should have a tag attached with his name and department.Each operators lock should have a tag attached with his name and department.
Each operators lock should have a tag attached with his name and department.Each operators lock should have a tag attached with his name and department.
Each operators lock should have a tag attached with his name and department.
Safety lock & id tag toSafety lock & id tag to
Safety lock & id tag toSafety lock & id tag to
Safety lock & id tag to
be placed in this area.be placed in this area.
be placed in this area.be placed in this area.
be placed in this area.