What to do if my InfiRay Thermal cameras riflescope can't connect to my smartphone or tablet?
If your InfiRay Thermal cameras riflescope can't connect to your smartphone or tablet, it could be due to a wrong Wi-Fi password. Ensure you input the correct password. Alternatively, too many Wi-Fi signals around the device may interfere with the connection. Try moving the device to an area with fewer Wi-Fi signals.
How to fix an InfiRay Thermal camera riflescope that won't turn on?
If your InfiRay Thermal camera riflescope won't turn on, the batteries may be completely discharged. Charge the battery to resolve this issue.
Why won't my InfiRay Thermal camera riflescope work with an external power supply?
If your InfiRay Thermal camera riflescope isn't working with an external power supply, the USB cable might be damaged. Try replacing the USB cable. Also, the external power source itself could be discharged, so check the external power source.
How to fix a fuzzy image on InfiRay Thermal cameras?
If the image on your InfiRay Thermal cameras is fuzzy, not clear, or unbalanced, it indicates that calibration is required. Perform image calibration according to the Calibration section of this manual.
What to do if Wi-Fi signal is missing or interrupted on InfiRay Thermal cameras?
If the Wi-Fi signal is missing or interrupted on your InfiRay Thermal cameras, the smartphone or tablet may be out of range of a strong Wi-Fi signal, or there may be obstacles. Replace the device until Wi-Fi signal is stable.
Why does the aiming reticle shift after firing rounds on my InfiRay Thermal cameras riflescope?
If the aiming reticle shifts after firing rounds on your InfiRay Thermal cameras riflescope, it may not be securely mounted, or the mount may not be fixed on the riflescope. Check that the riflescope has been securely mounted. Also, ensure you are using the same type and caliber of bullets as when the riflescope and weapon were initially zeroed. A slight shift is possible if the riflescope was zeroed in summer and is being used in winter, or vice versa.
How to brighten a dark image on InfiRay Thermal cameras?
If the image on your InfiRay Thermal cameras is too dark, the brightness level is likely too low. Adjust the screen brightness.
How do I fix an InfiRay Thermal cameras riflescope that will not focus?
If your InfiRay Thermal cameras riflescope will not focus, adjust the riflescope according to the Powering On and Image Setting section. Check the outer surfaces of the objective lenses and eyepiece and, where necessary, wipe them free of dust, condensation, frost, etc. In cold weather, you can use special anti-fogging coatings.
What causes a clear GUI but a blurry image on InfiRay Thermal cameras?
If the GUI is clear but the image is blurry on your InfiRay Thermal cameras, the lens is not focused. Adjust the image sharpness by rotating the lens adjuster.
How to clean dust or condensate on InfiRay Thermal cameras lens?
To clean dust or condensate on the lens of your InfiRay Thermal cameras, wipe off the outside optical surfaces with a soft cotton cloth. Allow the riflescope to dry by leaving it in a warm environment for 4 hours.
Covers environmental, swallowing, and operational safety guidelines for the device.
Details the effect of short and long presses for Power, Zoom, Menu, and Photography buttons.
Critical warnings for battery handling, charging, and usage to prevent damage or fire.
Steps for attaching the rifle mount to the scope and weapon.
Guide to turning on the device and adjusting image parameters like brightness and contrast.
Detailed steps for the 'Freeze' zeroing method to align reticle with impact.
Setting zeroing distance and adjusting reticle to match impact point.
Explains Automatic, Manual, and Background calibration modes.
Details how to change image mode, brightness, sharpness, and zeroing distance.
Explains how to access and adjust options like Ultraclear mode.
Selecting between Automatic, Manual, and Background calibration.
Options for setting zeroing profile, reticle type, and color.
Setting zeroing distance and executing the zeroing function.
Moving the reticle to match impact point and saving the settings.
How to set a new zeroing distance value.
Setting effective range, target type, and height for ranging.
Provides a table of common issues and corrective actions for operation.
Solutions for reticle shift, focus issues, and Wi-Fi connectivity problems.
General| Pixel Size | 12 μm |
|---|---|
| Frame Rate | 25 Hz |
| Operating Temperature | -20°C to +50°C |
| Storage Temperature | -40°C to +70°C |
| Ingress Protection | IP54 |
| Spectral Range | 8-14μm |
| Display Resolution | 640x480 |
| Battery Type | Li-ion |
To Next Page