Ingenico iCT 200 Series - COMMUNICATION SETUP; Set Communication Priority; Ethernet Communication Setup; Bluetooth Setup

Quick Reference Guide
May 2012
COMMUNICATION SETUP
Set Communication
Priority
1.
Press [Admin] key
2.
Enter Admin Name and press
[OK]
3.
Enter Admin Password and
press [OK]
4.
Select 3- SETUP MENU
5.
Select 2- COMMUNICATIONS
6.
Select COMSPRIORITY
7.
Enter COM MODE PRIORITY
ORDER.
Note: <ComsPriority> = ###
where 1 = Dial, 2= Ethernet (2 in
GPRS terminal means, GPRS
communication using IP
protocol)
Dial Communication
Setup
1.
Press [Admin] key
2.
Enter Admin Name and press
[OK]
3.
Enter Admin Password and
press [OK]
4.
Select 3- SETUP MENU
5.
Select 2- COMMUNICATIONS
6.
Select 2- DIAL
7.
Select 1- AccessCode (enter it
if needed) and press OK
8.
Select 2- Phone #s
9.
Select 1- PriAuthNum (enter
the primary auth number)
and press OK
10.
Select 2- SecAuthNum (enter
the secondary auth number)
and press OK
11.
Select 3- PriSetlNum (enter
the primary settlement
number) and press OK
12.
Select 4- SecSetlNum (enter
the secondary settlement
number) and press OK
13.
Select 3- Baud (select the
proper baud rate)
14.
Select 4- DialRetry (enter
the dial retry)
15.
.
Select 5- DialTone (Turn it on
or off)
16.
Select 6- DialType (select
Tone or Pulse)
17.
Select 7- PreDial (Turn it on or
off)
18.
Press CAN to return to the main
screen
Ethernet Communication
Setup
1.
Press [Admin] key
2.
Enter Admin Name and press
[OK]
3.
Enter Admin Password and
press [OK]
4.
Select 3- SETUP MENU
5.
Select 2- COMMUNICATIONS
6.
Select 3- Ethernet
7.
Select 2- Ethernet Setup
8.
Select 1- Dynamic IP
8.1 – Select 1- HostPort1 (enter
the primary Host port
number) and press OK
8.2 – Select 2- HostPort2
(enter the secondary Host
port number) and press OK
8.3 – Select 3- HostURL1 (enter
the primary Host URL
address) and press OK
8.4 – Select 4- HostURL2
(enter the secondary Host
URL address) and press OK
OR
9.
Select 2- Static IP
9.1 – Select 1- Terminal IP
(enter the terminal IP) and
press OK
9.2 – Select 2- GatewayIP
(enter the gateway IP) and
press OK
9.3 – Select 3- IPSubMask
(enter the IP subnet mask)
and press OK
9.4 – Select 4- PriDNSIP (enter
the primary DNS address) and
press OK
9.5 – Select 5- SecDNSIP
(enter the secondary DNS
address) and press OK
9.6 – Select 6- HostPort1
(enter the primary Host port
number) and press OK
9.7 – Select 7- HostPort2
(enter the secondary Host
port number) and press OK
9.8 – Select 8- HostURL1
(enter the primary Host URL
address) and press OK
9.9 – Select 9- HostURL2
(enter the secondary Host
URL address) and press OK
10.
Press CAN to return to the
ETHERNET MENU
11.
Select 3- Timers Setup
12.
Select 1- IPConnTimeout
(enter the IP connection
timeout) and press OK
13.
Press CAN to return to the
main screen
Bluetooth
Setup
1.
Press [Admin] key
2.
Enter Admin Name and press
[OK]
3.
Enter Admin Password and
press [OK]
4.
Select 3- SETUP MENU
5. Select 2- COMMUNICATIONS
6.
Select 4- Bluetooth
7.
Select 1- New Base
8.
Terminal displays Dock the
terminal on the base, dock
the terminal on the base
9.
Terminal displays BASE
ASSOCIATION OK
10.
Press CAN to return to the
main screen
GPRS
Setup
1.
Press [Admin] key
2.
Enter Admin Name and press
[OK]
3.
Enter Admin Password and
press [OK]
4.
Select 3- SETUP MENU
5.
Select 2- COMMUNICATIONS
6.
Select 4- GPRS
7.
Select 1- APN (enter the APN
address) and press OK
8.
Select 2- Login (enter the
login name) and press OK
9.
Select 3- Password (enter the
password) and press OK
10.
Select 4- SIM Code (enter the
SIM CODE) and press OK
11.
Press CAN to return to the
main screen