15
> Specifications > Advanced Setup > Listening Modes
> Network Functions > Basic Manual
|Troubleshooting Supplementary Information, etc.
Setting Item Default Value Setting Details
Height 2 Right 9' 0" / 2.70 m Specify the distance between each speaker and
the listening position.
•
Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Surround Right 7' 0" / 2.10 m Specify the distance between each speaker and
the listening position.
Surr Back Right 7' 0" / 2.10 m Specify the distance between each speaker and
the listening position.
•
Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Surr Back Left 7' 0" / 2.10 m Specify the distance between each speaker and
the listening position.
•
Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Surround Left 7' 0" / 2.10 m Specify the distance between each speaker and
the listening position.
Subwoofer 1 12' 0" / 3.60 m Specify the distance between each speaker and
the listening position.
Subwoofer 2 12' 0" / 3.60 m Specify the distance between each speaker and
the listening position.
•
Default values vary depending on the regions.
•
Distance units can be switched by pressing Mode on the remote controller. When the unit is set as
feet, you can set between 0' 0" 1/2 and 30' 0" in increments of 1/2. When the unit is set as meters,
you can set between 0.01 m and 9.00 m in increments of 0.01 m.
■ 4. Level Calibration
Setting Item Default Value Setting Details
Front Left 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Center 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Front Right 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Height 1 Left 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
•
Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Height 1 Right 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
•
Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Height 2 Left 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
•
Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
Height 2 Right 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
•
Depending on the use of the ZONE speakers, it
may not be possible to select this setting.
To Next Page
Loading...
Need help?
General
