Integra DTR-40.2 User Manual

104 pages

To Next Page

AV Receiver

DTR-40.2

Instruction Manual

Default Chapter2
- Introduction2
Important Safety Instructions2
Precautions3
Supplied Accessories4
- Using the Remote Controller4
- Table of Contents5
Features6
Front & Rear Panels8
- Front Panel8
- Display9
- Rear Panel10
Remote Controller11
- Controlling the AV Receiver11
About Home Theater12
- Enjoying Home Theater12
- Connections13
Connecting the AV Receiver13
- Connecting Your Speakers13
- Connecting a Power Amplifier16
- About AV Connections17
- Connecting Your Components with HDMI18
- Connecting Your Components19
- Connecting Integra/Onkyo U Components20
- Connecting Antenna21
- Connecting the Power Cord21
- Which Connections Should I Use22
- Turning on & Basic Operations24
Turning On/Off the AV Receiver24
- Turning on24
- Turning off24
Basic Operations25
- Selecting the Language Used for the Onscreen Setup Menus25
- Playing the Connected Component25
- Displaying Source Information25
- Setting the Display Brightness25
- Muting the AV Receiver26
- Using the Sleep Timer26
- Selecting Speaker Layout26
- Using the Home Menu26
- Changing the Input Display27
- Using Headphones27
- Using Easy Macros27
- Audyssey Multeq ® Room Correction and Speaker Setup28
Listening to the Radio31
- Using the Tuner31
- Presetting FM/AM Stations32
- Listening to SIRIUS Satellite Radio ® (North American Models)32
- Using RDS (Australian Models)38
Recording40
Using the Listening Modes41
- Selecting Listening Modes41
- About Listening Modes42
- Advanced Operations47
Advanced Setup47
- On-Screen Setup Menus47
- Common Procedures in Setup Menu47
- Input/Output Assign48
- Speaker Setup50
- Audio Adjust54
- Source Setup55
- Listening Mode Preset59
- Miscellaneous60
- Hardware Setup60
- Lock Setup63
- Using the Audio Settings63
Net/Usb66
- About NET66
- Connecting the AV Receiver66
- Listening to Internet Radio67
- Playing Music Files on a Server68
- Remote Playback from Media Server/Personal Computer71
- Network Settings72
- About USB74
Multi Zone76
- Connecting Zone 276
- Setting the Powered Zone 277
- Setting the Multi Zone78
- Using Zone 278
- Using the 12V Triggers80
- Using the Remote Controller in81
- Zone 2 and Multiroom Control Kits81
- Controlling Ipod & Other Components82
Controlling Ipod82
- Connecting the Ipod Directly to the USB Port82
- Connecting an Onkyo Dock83
- Using the Onkyo Dock84
- Controlling Your Ipod85
Controlling Other Components87
- Preprogrammed Remote Control Codes87
- Looking up for Remote Control Code87
- Entering Remote Control Codes88
- Remote Control Codes for Integra/Onkyo Components Connected Via U88
- Resetting Remote Mode Buttons89
- Resetting the Remote Controller89
- Controlling Other Components89
- Learning Commands91
- Using Normal Macros92
- Others93
Troubleshooting93
Specifications98
About HDMI100
Using an RIHD-Compatible TV, Player, or Recorder101
Video Resolution Chart103

Other manuals for Integra DTR-40.2

Firmware Update8 pages

Need help?

Do you have a question about the Integra DTR-40.2 and is the answer not in the manual?

Integra DTR-40.2 Specifications

General

Channels	7.2
HDMI Inputs	6
HDMI Outputs	2
Network Capability	Yes
THD (Total Harmonic Distortion)	0.08%
HDMI Version	1.4a
Audio Formats Supported	Dolby TrueHD, DTS-HD Master Audio, Dolby Digital Plus
Streaming Services	Pandora, SiriusXM, vTuner
Input Sensitivity/Impedance	200 mV/47 kΩ
Video Inputs/Outputs	Component
Audio Inputs/Outputs	Analog, Digital Optical, Digital Coaxial
Signal-to-Noise Ratio	106 dB