Ithaca ITHERM 280 - Page 79

iTherm
®
280 Programmer’s Guide Programming Codes
28-07764 Rev C Page 77
Description
ASCII Hex IPCL equivalent
code
Page
Reverse line feed.
[ESC] ] 1BH,5DH &%LR 90
Character Pitch
Set character spacing in points
[ESC]+I<n> 1BH 2BH
49H
None 276
Set character spacing in ¼ points
[ESC]+i<n> 1BH 2BH
69H
None 277
Set character spacing in points with
adjustment
[ESC]+J<n> 1BH 2BH
4AH
None 277
Set character spacing in ¼ points with
adjustment
[ESC]+j<n> 1BH 2BH
6AH
None 278
Begin 10 CPI character pitch.
[DC2] 12H &%F3 93
Begin 12 CPI character pitch.
[ESC] : 1BH,3AH &%F2 93
Begin 17 CPI character pitch.
[SI] 0FH &%F1 93
Set character pitch.
[ESC] [ P <n> 1BH,5BH,
50H
&%F<n> 94
Set inter-character spacing.
[ESC] V <n> 1BH,56H none 95
Begin 24 CPI character pitch
[ESC][SI] 1BH,0FH &%F4 93
Select Minimum character Height and
Width in ¼ points
[ESC] + p<w><h> 1BH 70H none 278
Set left/right print margins.
n
1
= Left margin, n
2
= Right margin
[ESC] X <n
1
><n
2
> 1BH,58H none 161
Character Font
Select font
[ESC] + 3 <ID> 1BH 2BH
31H
none 270
Select font by name
[ESC] + N
Filename<0>
1BH 2BH
4EH
none 271
Define Stacked Font
[ESC] + S <ID
1
>
<ID
2
> …
1BH 2BH
53H
none 270
Set stroke font Brush Size
[ESC] + B <w> 1BH 2BH
42H
none 279
Select Minimum character Height and
Width in points
[ESC] + P<w><h> 1BH 50H none 278
Select Minimum character Height and
Width in ¼ points
[ESC] + p<w><h> 1BH 70H none 278
Begin 12 x 12 draft print.
[ESC] # <0> 1BH,23H,
00H
&%QT 96
Set print quality mode.
n=0 Draft (12 x 12)
n=1 Large draft (12 x 14)
n=2 NLQ (24 x 16)
n=3 NLQ (24 x 16)
n=4-7 Repeats 0-3
[ESC] I <n> 1BH,49H &%QT {n=0}
&%QU {n=1}
&%QL {n=2}
&%QS {n=3}
96
Begin rotated font. (See command
description).
[ESC] P <n> 1BH,50H &%RI
&%RF
&%RN
97
Select character code page.
[ESC] [ T <n
h
> <n
l
> 1BH,5BH,
54H
&%CP <m
1
>
<m
2
> <m
3
> <m
4
>
101
Insert Euro character.
[ESC] [ C <n> 1BH,5BH,
43H
&%EU 102
Print control character.
[ESC] ^ <n> 1BH,5EH &%CC <m
1
>
<m
2
> <m
3
>
102
Redefine character set.
[ESC] [ S … 1BH,5BH,
53H…
104
Define user-defined characters.
[ESC] = <y> <c
1
>
<c
2
>…
1BH,3DH none 105
Enable user-defined characters.
[ESC] > <n> 1BH,3EH none 106
Cancel user-defined characters.
[ESC] $ 1BH,24H none 106