Ithaca ITHERM 280 - Quick Pcos Reference Chart

Programming Codes iTherm
®
280 Programmer’s Guide
Page 76 Rev C 28-07764
Quick PcOS Reference Chart
Description
ASCII Hex IPCL equivalent
code
Page
Low Level paper Motion
Line feed.
[LF] 0AH &%LF 82
Carriage return.
[CR] 0DH &%CR 82
Horizontal Motion
Back space.
[BS] 08H &%BS 83
Horizontal tab.
[HT] 09H &%HT 83
Set horizontal tab stops.
[ESC] D <n1> <n2>
... <ni> <0>
1BH,44H none 83
Set horizontal position.
[ESC] n <n1> <n2> 1BH,6EH &%HP<m1>
<m2> <m3>
84
Set justification.
n=0 Left
n=1 Center
n=2 Right
n=8 Left (No line feed)
n=9 Center (No line feed)
n=10 Right (No line feed)
[ESC] a <n> 1BH,61H &%JR {n=2}
&%JC {n=1}
&%JL {n=0}
84
Reset horizontal and vertical tab stops.
[ESC] R 1BH,52H &%HV 84
Set left/right print margins.
n
1
= Left margin, n
2
= Right margin
[ESC] X <n
1
><n
2
> 1BH,58H none 161
Select Minimum character Height and
Width in points
[ESC] + P<w><h> 1BH 50H none 278
Select Minimum character Height and
Width in ¼ points
[ESC] + p<w><h> 1BH 70H none 278
Ver
tical Motion
Perform a fine line feed.
[ESC] J <n> 1BH,4AH &%FM <m
1
>
<m
2
> <m
3
>
85
Set 1/8-inch line spacing.
[ESC] 0 1BH,30H &%ST 86
Set 7/72-inch line spacing.
[ESC] 1 1BH,31H &%SG 86
Begin variable line spacing. (Enable [ESC]
A <n>).
[ESC] 2 1BH,32H none 87
Set variable line spacing to n/216 inch.
[ESC] 3 <n> 1BH,33H &%SV <m
1
>
<m
2
> <m
3
>
85
Set variable line spacing to n/72 inch.
[ESC] A <n> 1BH,41H none 86
Feed <n> lines at current spacing.
[ESC] d <n> 1BH,64H &%FL <m
1
>
<m
2
>
87
Set vertical tab stops.
[ESC] B <n
1
> <n
2
>
<n
3
>...<n
i
> 0
1BH,42H none 88
Vertical tab.
[VT] 0BH &%VT 88
Form feed.
[FF] 0CH &%FF 89
Feed to black dot
[ESC][VT] 1BH,0BH None 91
Set top of form.
[ESC] 4 1BH,34H &%TF 89
Set form length in lines.
[ESC] C <n> 1BH,43H &%SL <m
1
>
<m
2
>
89
Select Minimum character Height and
Width in points
[ESC] + P<w><h> 1BH 50H none 278
Select Minimum character Height and
Width in ¼ points
[ESC] + p<w><h> 1BH 70H none 278
Begin auto line feed. (n=0, end n=1)
[ESC] 5 <n> 1BH,35H &%CA {n=0}
&%MA {n=1}
90
Set form length in inches.
[ESC] C [NUL] <n> 1BH,43H &%SI <m
1
>
<m
2
>
89