EasyManua.ls Logo

Jet JDP-20EVS-110 - User Manual

Jet JDP-20EVS-110
36 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Operating Instructions and Parts Manual
20” Electronic Variable Speed Drill Press
Models: JDP-20EVS-110, JDP-20EVST-230,-460
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-354220
Ph.: 800-274-6848 Edition 2 03/2017
www.jettools.com Copyright © 2017 JET
JDP-20EVST-230 shown

Table of Contents

Questions and Answers

  • S
    Suzanne WilliamsAug 7, 2025
    Why is my Jet Power Tool motor overheating?
    • D
      Dawn HicksAug 7, 2025
      Your Jet Power Tool motor might be overheating due to several reasons: a fault in the electrical circuit, which requires checking the current draw against the motor plate rating; using an oversize drill, which means you should reduce the drill size; excessive feed, so reduce the feed rate; or using no cutting fluid or the wrong type, so ensure you're using the correct cutting fluid for the material and drill.
  • P
    Paul SmithAug 11, 2025
    What to do if my Jet Power Tool spindle does not turn?
    • A
      Ashley MorrisAug 11, 2025
      If the spindle on your Jet Power Tool isn't turning, here are a few things to check: * The motor overload protector might have tripped, so press the motor overload reset button. * The circuit breaker might have tripped, so reset it. * The branch circuit breaker might have tripped or the fuse blown, so reset the breaker or replace the fuse. * There might be an open wire in the switch circuit, so repair the open circuit. * The switch might be defective, so replace it. * The drive belt might be broken, so replace the drive belt.
  • H
    Hannah MaciasAug 15, 2025
    Why does my Jet Power Tool drill stall?
    • M
      Marcus DavisAug 15, 2025
      Your Jet Power Tool drill might stall because of a worn drive belt. Check the belt's condition and replace it if it's glazed or slipping on the pulleys. It could also be due to an excessive feed rate for the drill size and material, or using no or improper cutting fluid. Reduce the feed pressure or use the correct cutting fluid.
  • M
    Monique NguyenAug 20, 2025
    Why does my Jet Power Tool produce poorly drilled holes?
    • M
      markacevedoAug 20, 2025
      Poorly drilled holes from your Jet Power Tool can be caused by several factors. The drill might be dull, requiring sharpening. There might be a lack of rigidity in your hold-down method, so check that all T-slot hold-downs, table-lock, and drill head bolts are tight. The speed might be too fast for the material and drill size, so check speed recommendations and reduce speed if necessary. The feed might be too fast, so reduce the feed rate. You might be using no or improper cutting fluid, so use or change to the proper fluid or coolant. Finally, the drill bit might be improperly ground, so check the angles and reliefs and regrind to the proper geometry.
  • S
    Shannon NewmanAug 25, 2025
    How to fix a noisy spindle on my Jet Power Tool?
    • R
      russellkathleenAug 25, 2025
      A noisy spindle on your Jet Power Tool could be due to damaged spindle bearings, in which case you should replace the bearings. Another possible cause is a worn spline, which would require replacing the spline.
  • J
    jcuevasAug 28, 2025
    Why does the Jet Power Tool table cannot be raised?
    • K
      Krista GonzalezAug 28, 2025
      The table on your Jet Power Tool might not raise due to a lack of lubrication. Lubricate the necessary parts to resolve this.
  • W
    Wendy CantrellSep 1, 2025
    What to do if there is no speed readout on my Jet Power Tool?
    • M
      Michael ContrerasSep 1, 2025
      If there's no speed readout on your Jet Power Tool, the speed pickup might be out of adjustment or have failed. Try adjusting the gap between the speed pickup and the post spindle pulley. If there's still no readout on the LED speed indicator after adjusting the gap, replace the speed pickup.

Jet JDP-20EVS-110 Specifications

General IconGeneral
TypeDrill Press
Motor Power1 HP
MotorInduction
Table Size14 in
Spindle Travel6 in
Number of Spindle Speeds12
Spindle TaperMT2
Swing20 inches
Drilling Capacity Steel1 inch
Drill Chuck Capacity5/8 in

Related product manuals