JVC HR-XVS20E - Page 31

EN
31
E
Set the tape speed.
Press
SP/LP/EP
(
p
).
● It is not possible to select EP mode if “COLOUR SYSTEM” is
set to “MESECAM”. (
墌
pg. 74)
F
Set the VPS/PDC mode.
Press
VPS/PDC
(
number key “7”
) to select “ON” or
“OFF”.
● If “VPS/PDC ON” is displayed on the TV screen, “VPS/PDC” is
set to “ON”.
● If “VPS/PDC OFF” is displayed on the TV screen, “VPS/PDC”
is set to “OFF”.
墌
“VPS/PDC Recording” on page 33.
G
Return to the normal screen.
Press
PROG
or
OK
. “PROGRAM COMPLETED” appears
on the TV screen for about 5 seconds, then the normal
screen appears.
● Repeat steps
B
–
G
for each additional programme.
H
Engage the unit’s timer mode.
Press
#
(
TIMER
). The unit turns off automatically and
“
#
” appears on the front display panel.
● To disengage the timer mode, press
#
(
TIMER
) again.
NOTES:
● To Change The Stop Time:
— press
STOP +/–
after pressing
OK
in step
D
. You can
compensate for anticipated programme schedule delays.
● To Timer-Record Weekly Or Daily Serials:
— after pressing
OK
in step
D
, press
WEEKLY
(
number key
“9”
) for weekly serials or
DAILY
(
number key “8”
) for daily
serials (Monday — Friday). Either “WEEKLY” or “DAILY”
appears on the TV screen. Pressing the button again makes the
corresponding indication disappear.
● You can programme this unit to timer-record as many as 8
programmes. If you try to programme the unit to record a
ninth, “PROGRAM FULL” appears on the TV screen and
“FULL” appears on the front display panel. To record the extra
programme, you must first cancel any unnecessary
programmes. (
墌
pg. 34)
● If there is a conflict in the timer schedule and one programme
overlaps with another, the programme starting earlier or
programme with the lower programme number will be
recorded.
Satellite Receiver Users
To timer-record a satellite broadcast using the S
HOW
V
IEW
system:
A Set “L-2 SELECT” to “A/V”. (
墌
pg. 61)
B Perform steps
A
–
H
.
C Set the satellite receiver to the appropriate channel before
the selected programme begins.
D Leave the satellite receiver’s power on.
ATTENTION
Guide Program Number
“Guide Program number” refers to the assigned TV station
numbers, according to broadcast area, for the S
HOW
V
IEW
timer recording. The Guide Program numbers can be found
in most TV listings.
If the Guide Program numbers are not set properly when you
timer-record a TV programme using the S
HOW
V
IEW
system,
the unit will record a TV programme of a different station.
When programming the timer using the S
HOW
V
IEW
system,
be sure to check the desired channel is selected correctly.
Set the Guide Program numbers only in the following cases:
● When timer-programming with the S
HOW
V
IEW
system, the
channel position, where the station you wish to record is
received on your unit, is not selected.
OR
● When timer-programming with the S
HOW
V
IEW
system, “TV
PROG” shows “– –”.
OR
● When you add a channel after Auto Set Up, Preset
Download or Auto Channel Set has taken place.
OR
● When you wish to timer-record a satellite programme with
the S
HOW
V
IEW
system.
Guide Program Number Set
A Perform steps
A
–
D
of “S
HOW
V
IEW
®
Timer Programming”
(
墌
pg. 30).
B Press
PR +/–
to input the channel position number on
which your unit receives the station, then press
OK
or
e
to set the Guide Program number.
C Perform steps
E
–
H
.