English–4
Bosch eBike Systems 0 276 001 Y45 | (12.10.12)
When the drive HMI is removed from holder 4, the last indicat-
ed assistance level is stored; the motor-output indicator a re-
mains empty.
Switching Start-assistance On/Off
The start-assistance function can be used for additional sup-
port on the first meters when starting is difficult (e. g., at a
traffic light or when starting uphill).
The start-assistance function may only be used when
starting (driving off) the eBike. Danger of injury when
the wheels of the eBike do
not h
ave ground contact while
using the start-assistance function.
To activate the start-assistance function, press and hold the
“WALK” button 14 on the operating unit. The eBike’s drive is
activated.
The start-assistance function is switched off as soon as any
of the following incidents occur:
–You release “WALK” button 14,
–Y
ou press a
nother button on the drive HMI,
–You pedal in forward or quickly in backward direction,
–The wheels of the eBike are blocked (e. g., through braking
or running against an obstruction),
–Your speed exceeds 18 km/h.
Switching the Lighting On/Off
Depending on country-specific regulations, two lighting ver-
sions are possible:
–The front light, rear light and display backligh
t can be
switched on and off at the same time via the drive HMI.
In this version, “Lights on” is displayed for approx. 1 s in
text indication c when switching on, and “Lights off” when
switching off.
– Only the display backlight can be switched on and off; the
front and rear light of the eBi
ke are independent of t
he
drive HMI.
For both versions, the lighting is switched on and off by
pressing button 2.
Speed and Distance Indication
The speed indication e always displays the current speed.
The following functions are available in the function indica-
tion (combination of text indication c and value indication d):
–“Range”: Estimated range of the available battery-pack
charge (for constant conditions such as assistance level,
route profile, etc.)
–“Distance”: Distance covered since the last reset
–“Tr
ip
time”: Trip time since the last reset
–“Avg. Speed”: Average speed achieved since the last reset
–“Max. Speed”: Maximum speed achieved since the last re-
set
–“Clock”: Current time
To switch between the indication functions, press the “i”
button 1 on the drive HMI or the “i” button 11 on the operating
unit until the desired function is displayed.
To reset “Distance”, “Trip time” and “Avg. Speed”, switch to
any of the three functions and then press and hold the
“RESET” button 6 unti
l th
e indication is set to zero. This also
resets the values of the other two functions.
To reset the “Max. Speed”, switch to this f
unction and then
press and hold the “RESET” button 6 until the indication is set
to zero.
When the drive HMI is removed from the holder 4, all function
values remain stored and can be viewed.
Displaying/Adapting Basic Settings
The basic settings can be displayed and changed no matter if
the drive HMI is
i
n the holder 4 or not.
To access the basic settings menu, press and hold the
“RESET” button 6 and the “i” button 1 until “Configuration”
is displayed in text indication c.
To switch between the basic settings, press the “i” button 1
on the drive HMI until the desired basic setting is displayed.
When the drive HMI is inserted in holder 4, you can also
press
th
e “i” button 11 on the operating unit.
To change the basic settings, press the On/Off button 5 next
to the “ –” indication to decrease the value or scroll down, or
the illumination button 2 next to the “+” indication to increase
the value or scroll up.
When the drive HMI is inserted in holde
r 4, you can also
ch
ange the values with the “ –” button 12 or the “+” button 13
on the operating unit.
To exit the function and store a changed setting, press the
“RESET” button 6 for 3 s.
The following basic settings are available:
–“unit k
m
/mi”: The speed and distance can be displayed ei-
ther in kilometres or miles.
–“time format”: The time can be displayed either in the
12 hour or 24 hour format.
–“clock”: The current time can be set here. Pressing and
holding the setting buttons fast-forwards the setting
speed.
–“English”: The language for text indication can be
changed. The available languages are German, English,
French, Spanish, Italian and Dutch.
–“odometer”: Indicates the total distance tr
a
velled with the
eBike (not changeable).
–“power-on hours”: Indicates the total travel duration with
the eBike (not changeable).
Assistance Level Motor Output*
(Derailleur)
“ECO”
30 %
“TOUR”
100 %
“SPORT”
180 %
“TURBO”
250 %
*The motor output can vary for individual versions.
OBJ_BUCH-1557-002.book Page 4 Friday, October 12, 2012 12:14 PM
To Next Page
Loading...
