What causes no sparking or poor sparking in KEEWAY Matrix?
If your KEEWAY Scooter has no sparking or poor sparking, it may be due to a defective CDI & ignition coil unit, a defective spark plug, a defective magneto stator coil, or a loose connection of the lead wire. You should replace the defective components and connect/tighten any loose lead wires.
What causes overflow and fuel level fluctuations in KEEWAY Matrix?
If you are experiencing overflow and fuel level fluctuations in your KEEWAY Scooter, it could be due to a needle valve that is worn or damaged, a spring in the needle valve that is broken, a float that is not working properly, foreign matter that has adhered to the needle valve, or a fuel level that is too high or low. You should replace the needle valve and spring if necessary, check and adjust the float, clean any foreign matter from the needle valve, and adjust and replace the fuel level if needed.
Why do the spark plug electrodes on my KEEWAY Matrix overheat or burn?
If the spark plug electrodes on your KEEWAY Scooter overheat or burn, it may be due to a spark plug that is too hot, the engine overheating, a spark plug that is loose, a mixture that is too lean, or not enough engine oil. You should replace the spark plug with a colder type, tune up the engine, retighten the spark plug, adjust the carburetor, and check the oil pump.
What causes the magneto to not charge in KEEWAY Scooter?
If the magneto in your KEEWAY Scooter does not charge, it could be due to an open or short in the lead wires, or loose lead connections, a shorted, grounded, or open magneto coil, or a shorted or open regulator/rectifier. You should repair or retighten the lead wires, and replace the magneto coil or regulator/rectifier if necessary.
General| Fuel System | Carburetor |
|---|---|
| Front Suspension | Telescopic fork |
| Front Brake | Disc |
| Rear Brake | Drum |
| Front Tire | 120/70-12 |
| Rear Tire | 130/70-12 |
| Width | 700 mm |
| Cooling System | Air cooled |
| Transmission | Automatic |
Lists essential tools for manual maintenance and repair procedures.
Details methods for identifying scooter models and component numbers.
Provides specifications for recommended fuel and engine oil types.
Outlines initial running-in guidelines for new scooters.
Highlights important safety warnings and general handling guidelines.
Lists technical specifications for the scooter's dimensions, weight, and components.
Details intervals and steps for regular maintenance tasks.
Covers servicing for key engine parts like spark plugs and cylinders.
Explains maintenance for air cleaners, oil pumps, and gear oil.
Covers inspection and maintenance of brake systems and tires.
Details maintenance for steering stem and shock absorbers.
Provides instructions for disassembling and reassembling engine parts.
Details the step-by-step process for engine reassembly.
Explains the inspection and replacement of bearings and oil seals.
Details procedures for inspecting crankshaft runout and bearing condition.
Outlines checks for proper automatic clutch engagement and operation.
Covers inspection for cracks, wear, and correct width of the drive belt.
Details inspection and maintenance of cylinder head and piston components.
Explains inspection and replacement procedures for the reed valve assembly.
Describes the operation and function of the fuel switch.
Provides specifications and adjustment details for the carburetor.
Explains the function and maintenance of the oil pump.
Details the components and inspection of the ignition system.
Explains the charging output check and lighting system components.
Covers starter motor removal, disassembly, and relay inspection.
Describes inspection procedures for the fuel gauge and indicator lights.
Illustrates the function and wiring of various scooter switches.
Provides guidelines for battery initial charging and maintenance.
Details the removal and installation of body panels and covers.
Covers the removal, inspection, and reassembly of the front wheel.
Explains brake pad replacement and caliper maintenance procedures.
Details the removal, disassembly, and inspection of the master cylinder.
Covers removal, inspection, and reassembly of steering and suspension.
Details removal, inspection, and reassembly of the rear wheel and brake.
Lists common problems, symptoms, causes, and remedies for the scooter.
Presents a schematic of the scooter's electrical system for diagnosis.
Illustrates the correct routing of wires, cables, and brake hoses.
Lists specialized tools required for various maintenance procedures.
Provides specific torque values for engine screw thread parts.
Lists key service data and specifications for engine components.
To Next Page
