Kenmore 79080329310 User Manual

Installation
Instructions
Overthe Range
Microwave Oven
I
Questions? Call 1-800-4-MY-HOME ®
or Visit our Website at: http://www.kenmore.com
I
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT - Savethese
instructions for local inspector's use.
• IMPORTANT - Observeall
governing codes and ordinances.
• Note to Installer - Be sure to leave these
instructions with the Consumer.
• Note to Consumer - Keep these
instructions for flJture reference.
• Skill level - Installation of this appliance requires
basic mechanical and electrical skills.
• Proper installation is the responsibility of the installer
• Product failure due to improper installation is not
covered under the Warranty.
READ CAREFU LLY.
KEEP THESE INSTRUCTIONS.
pin 316495111
May 2013

Kenmore 79080329310 Specifications

General

Model Number	79080329310
Brand	Kenmore
Color	Stainless Steel
Pre-Programmed Settings	Yes
Child Lock	Yes
Type	Countertop Microwave Oven

Summary

BEFORE YOU BEGIN

IMPORTANT SAFETY INSTRUCTIONS

ELECTRICAL REQUIREMENTS

DAMAGE-SHIPMENT/ INSTALLATION

PARTS INCLUDED

TOOLS YOU WILL NEED

MOUNTING SPACE

PLACEMENT OF THE MOUNTING PLATE

A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE

Procedure for safely unpacking the microwave oven and its components.

B. FINDING THE WALL STUDS

Methods for locating wall studs for secure mounting of the plate.

DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET

ALIGNING THE WALL PLATE

INSTALLATION TYPES

A OUTSIDE TOP EXHAUST (VERTICAL DUCT)

Instructions for venting the microwave exhaust vertically through the top.

B OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)

Instructions for venting the microwave exhaust horizontally through the back.

C RECIRCULATING (NON-VENTED DUCTLESS)

Instructions for installations where air is recirculated within the room.

OUTSIDE TOP EXHAUST (Vertical Duct)

A1. ATTACH THE MOUNTING PLATE TO THE WALL

Steps to securely attach the mounting plate to the wall using hardware.

A2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET

Using the template to prepare the top cabinet for installation.

A3. ADAPTING MICROWAVE BLOWER FOR OUTSIDE TOP EXHAUST

Modifying the microwave's blower for top exhaust ventilation.

A4. CHECK FOR PROPER DAMPER OPERATION

Verifying the functionality of the exhaust damper.

A5. MOUNT THE MICROWAVE OVEN

Steps to physically mount the microwave oven onto the prepared plate.

A6. ADJUST THE EXHAUST ADAPTOR

Adjusting the exhaust adaptor for proper connection to the ductwork.

A7. CONNECTING DUCTWORK

Connecting the house exhaust duct to the microwave's adaptor.

OUTSIDE BACK EXHAUST (Horizontal Duct)

B1. PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST

Cutting an opening in the rear wall for horizontal exhaust.

B2. REMOVE BLOWER PLATE

Procedure to remove the blower plate from the microwave unit.

B3. ATTACH THE MOUNTING PLATE TO THE WALL

Steps to securely attach the mounting plate to the wall using hardware.

B4. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET

Using the template to prepare the top cabinet for installation.

B5. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST

Modifying the microwave's blower for back exhaust ventilation.

B6. MOUNT THE MICROWAVE OVEN

Steps to physically mount the microwave oven onto the prepared plate.

RECIRCULATING (Non-Vented Ductless)

C1. ATTACH THE MOUNTING PLATE TO THE WALL

Steps to securely attach the mounting plate to the wall using hardware.

C2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET

Using the template to prepare the top cabinet for installation.

C3. CHECK BLOWER PLATE

Verifying the blower plate is correctly installed on the unit.

C4. MOUNT THE MICROWAVE OVEN

Steps to physically mount the microwave oven onto the prepared plate.

C5. INSTALLING OR CHANGE THE CHARCOAL FILTER (Some Models)

Procedure for installing or replacing the charcoal filter.

BEFORE YOU USE YOUR MICROWAVE