Need help?Do you have a question about the Kopp Free-control and is the answer not in the manual?
Explains the versatility and limitations of Free-control radio system transmission.
Illustrates signal loss based on wall thickness and distance from the transmitter.
Describes the 4 modes: switching, inching, dimming, and shutter control, selected via DIP switch.
Instructions for replacing the transmitter battery and expected battery life.
Specifies selecting Mode A and setting DIP switches to ON for switching mode.
Shows how to connect switches to input channels 1/2 and 3/4 for switching mode.
Specifies selecting Mode A and setting DIP switches to ON for two-circuit switching mode.
Illustrates connecting two-circuit switches to input channels 1/2 or 1/4, and 3/2 or 3/4.
Specifies selecting Mode B and setting DIP switches to OFF for pushbutton operation.
Shows connecting pushbuttons to input channels 1/2 and 3/4 for pushbutton mode.
Specifies selecting Mode B and setting DIP switches to OFF for sequence pushbutton operation.
Illustrates connecting sequence pushbutton contacts to input channels 1/2 and 3/4.
Specifies selecting Mode C, setting DIP 1 to ON and DIP 2 to OFF for dimming.
Shows connecting pushbuttons to input channels 1/2 and 3/4 for dimming mode.
Specifies selecting Mode C, setting DIP 1 to ON and DIP 2 to OFF for dimming.
Illustrates connecting sequence pushbuttons to input channels 1/2 and 3/4 for dimming.
Specifies selecting Mode D, setting DIP 1 to OFF and DIP 2 to ON for shutter control.
Shows connecting shutter switch contacts to input channels 1/2 and 3/4 for shutter mode.
Describes installation in flush-mounted boxes (min. 60mm depth) and surface-type enclosures.
Explains LED indicators on receivers for teach-in mode, acknowledgment, and faults.
Details LED indicators on the transmitter for signal transmission and low battery.
Instructions on how to delete the programmed assignment between transmitter and receiver.
Addresses issues where the transmitter is unresponsive, checking battery and connections.
Troubleshoots cases where the transmitter signals but the receiver doesn't react, suggesting teach-in issues.
Diagnoses intermittent receiver switching due to range limits or interference sources.
Addresses incorrect switching or permanent signal transmission due to wrong modus or wiring.
Explains the versatility and limitations of Free-control radio system transmission.
Illustrates signal loss based on wall thickness and distance from the transmitter.
Describes the 4 modes: switching, inching, dimming, and shutter control, selected via DIP switch.
Instructions for replacing the transmitter battery and expected battery life.
Specifies selecting Mode A and setting DIP switches to ON for switching mode.
Shows how to connect switches to input channels 1/2 and 3/4 for switching mode.
Specifies selecting Mode A and setting DIP switches to ON for two-circuit switching mode.
Illustrates connecting two-circuit switches to input channels 1/2 or 1/4, and 3/2 or 3/4.
Specifies selecting Mode B and setting DIP switches to OFF for pushbutton operation.
Shows connecting pushbuttons to input channels 1/2 and 3/4 for pushbutton mode.
Specifies selecting Mode B and setting DIP switches to OFF for sequence pushbutton operation.
Illustrates connecting sequence pushbutton contacts to input channels 1/2 and 3/4.
Specifies selecting Mode C, setting DIP 1 to ON and DIP 2 to OFF for dimming.
Shows connecting pushbuttons to input channels 1/2 and 3/4 for dimming mode.
Specifies selecting Mode C, setting DIP 1 to ON and DIP 2 to OFF for dimming.
Illustrates connecting sequence pushbuttons to input channels 1/2 and 3/4 for dimming.
Specifies selecting Mode D, setting DIP 1 to OFF and DIP 2 to ON for shutter control.
Shows connecting shutter switch contacts to input channels 1/2 and 3/4 for shutter mode.
Describes installation in flush-mounted boxes (min. 60mm depth) and surface-type enclosures.
Explains LED indicators on receivers for teach-in mode, acknowledgment, and faults.
Details LED indicators on the transmitter for signal transmission and low battery.
Instructions on how to delete the programmed assignment between transmitter and receiver.
Addresses issues where the transmitter is unresponsive, checking battery and connections.
Troubleshoots cases where the transmitter signals but the receiver doesn't react, suggesting teach-in issues.
Diagnoses intermittent receiver switching due to range limits or interference sources.
Addresses incorrect switching or permanent signal transmission due to wrong modus or wiring.
General| Width | 60 cm |
|---|---|
| Material | Stainless steel |
| Number of fan speeds | 3 |
| Lighting | LED |
| Type | Wall-mounted |
To Next Page