179
Song Play operating mode
Preferences: General Control
Reference
Note: When both players are in play, the Voice Pro-
cessor only receives notes from Player 1 when the X-
Fader slider is fully on the left, and only from Player
2 when the X-Fader slider is fully on the right.
Global Notes or chords received by the Voice Processor
depend on the “Harmony Mode” parameter (see
page 242):
• if the Chords option is selected, chords are sent
from the Chord Scanning area of the keyboard.
• if the Notes option is selected, notes are sent
(instead of chords).
• if the Shift or Scalic options are selected, notes
or chords are ignored.
Preferences: General Control
In this page, you can set various general parameters.
Note: These settings are stored in the Song Play Setup area of the
Global file (together with all the other parameters marked with the
abbreviation through the manual). After changing these
settings, select the Write Global-Song Play Setup command from
the page menu to save them to the Global.
Midi Setup
MIDI channels for the Song Play mode can be automatically
configured by selecting a MIDI Setup with this parameter. See
“MIDI Setup” on page 228 for more information on using MIDI
Setups.
Note: To automatically select a MIDI Setup when entering the
Song Play mode, select the Write Global-Song Play Setup command
from the page menu.
For detailed information on preloaded MIDI Setup settings, see
“MIDI Setup” on page 319.
Note: After selecting a MIDI Setup, you can go to the Global mode
and apply any change to each channel setting. To store these
changes to a MIDI Setup, while still in Global mode select the Write
Global-Midi Setup command from the page menu. All MIDI Set-
ups can be freely customized and overwritten.
Hint: To restore the original MIDI Setups, load the original Fac-
tory data again (available in the supplied Accessory CD, or down-
loadable from www
.korgpa.com).
Performance recalls FX CD
This parameter selects the effects mode for the Performance.
Off When selecting a Performance, no effect is
selected.
On The Performance selects the C/D effect pair.
Note: When both this parameter and the “Ply.2 FX
Mode” parameter are set to select the C/D effect
pair, Player 2 shares its effects with Keyboard
tracks. Therefore, these effects can be changed either
selecting a Song for Player 2, or selecting a Perfor-
mance.
Lyrics/Score X-Fader Link
This parameter allows you to use the X-FADER slider to select
the Player whose lyrics, chords, markers or score will be shown
in the built-in display or external monitor.
When the “Text Only” option is selected as the external display
view mode, the slider allows you to choose whose lyrics and
chords will be shown on the external monitor (see “External
Display” on page 235 for more information).
Off When moving the X-FADER, only the volume
balance between Songs will be selected. The
shown lyrics or markers will remain unchanged.
On When moving the X-FADER fully to the left or
the right, the corresponding Song will fade-in,
and its lyrics, chords, markers and score will be
selected and shown in the display or external
monitor.
Ply.2 FX Mode
This parameter selects the effects mode for Player 2. When a 4-
effects Song is loaded, all four effects are used, independently
from this setting.
AB The A and B effect pair is used. Player 2 shares its
effects with Player 1.
CD The C and D effect pair is used.
Note: When this parameter is set to CD, Player 2
shares its effects with Keyboard tracks, so these
effects can be changed either selecting a Song for
Player 2, or selecting a Performance (unless the
“Performance recalls FX CD” parameter is left
unchecked – see above).
Link Mode
When playing Standard MIDI Files, the two onboard Players can
work each one with a different Tempo (Off), or use both the
same Tempo (various Link modes). With MP3 files, each Song
has its own recorded tempo, and cannot be linked.
Sng
Sng
Sng
Sng
Lyrics
Markers
Player 1
Lyrics
Markers
Player 2
Sng
Sng
To Next Page
Loading...
