243
Appendices
F
File already exists
File contains unsupported data
File is read-only protected
File unavailable
File/path not found
Front sample data used in rear sample
Can’t overwrite
I
Illegal file description
Illegal SMF data
Illegal SMF division
Illegal SMF format
M
Master Track can’t be recorded alone
Measure size over limit
Measure number over limit
Media not formatted
Medium changed
Meaning: When executing a Create Directory or File
Rename operation, a directory or file of the same
name already exists on the media.
Meaning: When executing the Media mode utility menu
command “Copy” without using wild cards, the
copy destination contained a file of the same
name as the copy source.
Meaning: When you executed the Media mode utility “Save
Sampling Data” with a setting of All, All Multi-
samples, All Samples, or One Multisample, a
directory with the same name as the directory that
the TRITON Le attempted to create already
existed on the media.
Action: Either delete the existing directory or file, or spec-
ify a different filename.
Meaning: For an AIFF file etc., you attempted to load a file
format that the TRITON Le does not support.
Action: If possible, use a computer etc. to convert the data
into a format supported by the TRITON Le, and
load it.
Meaning: You attempted to write to a file or to delete a file
that had a read-only attribute.
Meaning: You attempted to save a file to a SmartMedia that
contained a read-only file of the same name.
Action: Save the file with a different name.
Meaning: You attempted to load or open a file whose format
was incorrect.
Meaning: When loading a sample file in Media mode, the
file name specified in the dialog box for selecting a
directory hierarchy or other media did not exist in
the specified location.
Meaning: When executing the Media mode utility menu
command “Delete,” the specified file did not exist.
Meaning: When executing the Media mode utility menu
command “Copy” and you used a wild card to
specify the copy file name, the specified file was
not found. Alternatively, the length of the copy
source path name exceeded 76 characters.
Meaning: In Media mode when you used the [F6] (“Open”)
key to open a directory, the path length including
the selected directory name exceeded 76 charac-
ters.
Action: Check the file or directory.
Meaning: When executing the Sampling mode function
Sample Edit “Link,” the sample data of the front
sample was also used by the rear sample, and
thus could not be overwritten.
Action: Do not use Overwrite; specify a different sample
as the save destination.
Meaning: The filename that you specified when saving a file
or creating a directory contained invalid charac-
ters.
Action: Change the filename you are specifying. Filena-
mes not permitted by MS-DOS cannot be used as
a filename.
Meaning: You attempted to load a file that was not a Stan-
dard MIDI File.
Meaning: You attempted to load a Standard MIDI File that
was timecode-based.
Meaning: You attempted to load a Standard MIDI File of a
format other than 0 or 1.
Meaning: When realtime-recording a single track, you
attempted to begin recording with the master
track as the current track.
Action: Begin recording with a track 1–16.
Meaning: When loading a Standard MIDI File, the number
of events in a measure exceeded the maximum
(approximately 10,000 events).
Meaning: The attempted edit operation would cause the
maximum number of events in a measure
(approximately 10,000) to be exceeded.
Action: Use event editing etc. to delete unwanted data.
Meaning: The attempted edit operation would cause the
track length to exceed 999 measures.
Action: Delete unnecessary measures.
Meaning: When you attempted to perform a high-level for-
mat (quick format) of media, the media had not
been physically formatted yet.
Action: Execute the Media mode utility menu command
“Format” to physically format the media (full for-
mat).
Meaning: When executing the Media mode Utility com-
mand “Copy,” the media was exchanged or
ejected, and it was not possible to copy between
separate media on the same drive.
To Next Page
Loading...
