What causes a KTM 690 SMC USA 2010 battery to discharge?
A KTM Motorcycle battery might discharge if: * The ignition was not switched off when the vehicle was parked: Recharge the battery. * The battery is not charged by the alternator: Check the charging voltage and quiescent current.
What to do if time is not correctly displayed on KTM 690 SMC USA 2010 Motorcycle?
If the time is not correctly displayed on your KTM Motorcycle, it may be due to fuse 2 being blown. Replace the fuse.
What to do if combination instrument shows nothing in the display of KTM 690 SMC USA 2010?
If the combination instrument display on your KTM Motorcycle is blank, check fuse 1 and replace it if it's blown.
General| Engine Type | Single cylinder, 4-stroke |
|---|---|
| Displacement | 654 cc |
| Bore x Stroke | 102 mm x 80 mm |
| Fuel System | Electronic Fuel Injection |
| Transmission | 6-speed |
| Rear Suspension | WP monoshock |
| Front Tire | 120/70 ZR 17 |
| Rear Tire | 160/60 ZR 17 |
| Starter | Electric |
| ABS | Optional |
| Seat Height | 890 mm |
| Fuel Capacity | 12 liters |
| Engine | Single cylinder, 4-stroke |
| Ignition | Digital |
| Front Suspension | WP 48 mm USD forks |
| Front Brake | Single disc, 320 mm |
| Rear Brake | Single disc, 240 mm |
| Frame | Steel trellis frame |
| Power | 46 kW (63 hp) at 7500 rpm |
Explains the meaning of symbols used in the manual for clarity.
Details the typographical and other formats used for consistent communication.
Defines the intended use of KTM sport motorcycles for road operation.
Emphasizes the importance of proper maintenance for operation and wear prevention.
Outlines conditions for warranty claims and the role of authorized workshops.
Advises on using specified fuels, oils, and greases according to manual recommendations.
Recommends using approved parts and installation by authorized workshops for safety.
Details requirements for special tools and replacement of non-reusable parts during assembly.
Provides notes and warnings regarding safe transport and preventing damage.
Addresses responsible motorcycle use and its impact on the environment and others.
Introduces the section detailing various warning labels affixed to the vehicle.
Highlights the importance of paying close attention to all notes and warnings for safety.
Defines different risk levels (Danger, Warning, Caution, Note) for hazard identification.
Stresses the importance of reading the manual for operation, handling, and servicing.
Instructs owners on reporting vehicle defects to NHTSA and KTM North America.
Details the warranty for the exhaust system concerning US federal noise standards.
Illustrates and labels components of the motorcycle from the front left perspective.
Illustrates and labels components of the motorcycle from the rear right perspective.
Indicates the location where the chassis number is stamped on the vehicle.
Shows the location of the vehicle's type label, typically on the frame.
Explains where to find the key number on the KEYCODECARD for ordering spare keys.
Specifies the location of the engine number stamped on the engine.
Identifies the location of the part number for the front fork.
Indicates where to find the part number for the rear shock absorber.
Describes the clutch lever, its location, and hydraulic operation.
Details the hand brake lever, its location, and function for the front brake.
Explains the function and positions of the light switch for low and high beams.
Describes the operation of the turn signal switch for left and right indicators.
Explains the location and operation of the horn button.
Details the function of the emergency OFF switch for interrupting the ignition circuit.
Explains the location and operation of the electric starter button.
Describes the ignition lock positions (OFF, ON, Steering locked) and key removal.
Introduces the instrument cluster and its four main function areas.
Explains how to change display modes and reset trip meters using buttons.
Describes the tachometer's display of engine speed and redline range.
Explains the function and meaning of various indicator lamps on the instrument cluster.
Details the display segments and function test upon ignition.
Explains the display of speed in km/h or mph.
Describes how to set the unit of distance measurement for the display.
Shows where the time is displayed and when it needs resetting.
Provides instructions on how to set the vehicle's clock.
Explains the ODO display for total distance traveled.
Details how to set and reset the TRIP 1 trip counter.
Outlines the procedure for setting and resetting the TRIP 2 trip counter.
Explains the TRIP F display that activates when fuel level is low.
Describes the coolant temperature display using bars and warning lights.
Guides on how to open the fuel filler cap using the ignition key.
Provides instructions for closing the fuel filler cap correctly.
Explains the purpose of the handrails for moving the motorcycle and passenger use.
Shows how to release the motorcycle seat using a strap.
Describes the folding mechanism of passenger footrests for use with or without a passenger.
Identifies the location of the shift lever on the engine.
Locates the foot brake lever and its function for the rear brake.
Explains the function and safety coupling of the side stand.
Offers crucial advice and warnings for initial operation and safety.
Provides guidelines for the engine running-in phase, including maximum speeds.
Details important considerations and warnings regarding vehicle loading and payload.
Lists essential checks to perform before riding the motorcycle for safety.
Guides on the procedure for starting the motorcycle engine safely.
Explains how to engage the first gear and start moving off smoothly.
Offers advice on gear shifting, load alterations, and braking during riding.
Provides warnings and advice on braking techniques and efficiency under various conditions.
Details procedures for stopping, parking, and securing the motorcycle.
Gives essential safety warnings and instructions for refueling the motorcycle.
Presents a schedule of maintenance tasks and recommended intervals for different models.
Instructions for safely lifting the front of the motorcycle using a work stand.
Steps to safely remove the front of the motorcycle from the work stand.
Guidance on safely lifting the rear of the motorcycle onto a work stand.
Procedures for safely removing the rear of the motorcycle from the work stand.
General overview of the fork and shock absorber for chassis adaptation.
Details how to adjust the fork's hydraulic compression damping.
Explains the process for adjusting the fork's hydraulic rebound damping.
Introduces dual compression control for the shock absorber.
Provides instructions for adjusting the low-speed compression damping of the shock absorber.
Details how to adjust the shock absorber's high-speed compression damping.
Explains the procedure for adjusting the shock absorber's rebound damping.
Guides on measuring the rear wheel's sag when the motorcycle is unloaded.
Details how to check the static sag of the rear shock absorber.
Explains the procedure for checking the riding sag of the shock absorber.
Provides instructions for adjusting the rear shock absorber's spring preload.
Guides on how to bleed the hydraulic system in the fork legs.
Details the process for cleaning the dust boots on the front fork legs.
Instructions for safely removing the fork protector.
Steps for correctly installing the front fork protector.
Explains how to check for play in the steering head bearing.
Provides instructions for adjusting the steering head bearing play.
Describes the options for adjusting the handlebar position for rider comfort.
Details the process of adjusting the handlebar position.
Guides on inspecting the drive chain for excessive dirt.
Provides instructions for cleaning the motorcycle's drive chain.
Explains how to check the drive chain tension.
Guides on inspecting the chain, rear, and engine sprockets for wear.
Details the procedure for adjusting the chain guide.
Explains how to inspect the brake discs for wear and damage.
Guides on adjusting the hand brake lever's position for ergonomics.
Details how to check the brake fluid level in the front brake reservoir.
Provides instructions on adding front brake fluid if the level is low.
Explains how to check the thickness of the front brake linings.
Guides on replacing the worn front brake linings.
Details the process for removing the front brake linings.
Explains how to check the free play in the foot brake lever.
Guides on adjusting the foot brake lever's position for proper engagement.
Details how to check the rear brake fluid reservoir level.
Provides instructions on adding rear brake fluid if the level is low.
Explains how to check the thickness of the rear brake linings.
Guides on replacing the worn rear brake linings.
Provides step-by-step instructions for removing the front wheel.
Details the process for correctly installing the front wheel.
Provides instructions for properly installing the rear wheel.
Explains how to inspect the rear hub rubber dampers for wear.
Guides on inspecting the tires for cuts, damage, tread depth, and age.
Details how to check the tension of the wheel spokes.
Explains the features and advantages of the tubeless tire system.
Guides on checking and adjusting tire air pressure for optimal performance.
Provides instructions for removing the motorcycle seat.
Details the process for correctly mounting the motorcycle seat.
Guides on the safe removal of the motorcycle battery.
Explains how to recharge the motorcycle battery safely.
Provides instructions for correctly installing the motorcycle battery.
Guides on replacing the main fuse protecting the vehicle's electrical system.
Details how to replace fuses for individual electrical components.
Explains how to adjust the engine's performance map using the Map-Select switch.
Guides on how to remove the headlight mask assembly.
Provides instructions for correctly installing the headlight mask.
Details the process for replacing the main headlight bulb.
Guides on replacing the small parking light bulb.
Explains how to replace the rear tail light and brake light bulb.
Details the procedure for replacing a turn signal (flasher) bulb.
Guides on how to check and verify the headlight's beam aim.
Explains how to adjust the headlight's beam height and range.
Provides instructions for removing the air filter for cleaning or replacement.
Details the process for correctly installing the air filter.
Introduces the cooling system components and their function.
Guides on checking the coolant level and antifreeze protection.
Details how to check the coolant level in the radiator and compensating tank.
Provides instructions for safely draining the motorcycle's coolant.
Guides on refilling the cooling system with the correct coolant.
Explains how to adjust the clutch lever's position for rider comfort.
Guides on checking and topping up the hydraulic clutch fluid.
Explains how to check for correct play in the throttle cable.
Details the procedure for adjusting the throttle cable play.
Guides on how to check the engine oil level when the engine is warm.
Outlines the process for an oil change and cleaning oil screens.
Provides instructions for safely draining the engine oil.
Guides on how to remove and replace the oil filter.
Details the process for correctly installing the oil filter.
Explains how to clean the engine's oil screens.
Guides on refilling the engine with the correct type and amount of oil.
Instructions for adding engine oil if the level is low.
Lists causes and actions for when the starter button fails to engage the engine.
Addresses issues where the engine only turns with the clutch lever pulled.
Covers common causes and solutions for an engine that cranks but won't start.
Helps diagnose and resolve issues related to reduced engine power.
Provides steps to troubleshoot engine overheating problems.
Explains the meaning of the FI warning lamp and possible causes.
Addresses situations where the engine stops running while riding.
Helps diagnose and resolve issues related to excessive engine oil consumption.
Troubleshooting steps for non-functioning headlights or parking lights.
Guides on troubleshooting issues with turn signals, brake, or horn.
Addresses problems with the display of time on the instrument cluster.
Covers causes and solutions for a discharged motorcycle battery.
Troubleshooting steps when the instrument cluster display is blank.
Helps diagnose issues with the speedometer function.
Identifies a crankshaft position sensor circuit fault indicated by blink code 02.
Indicates throttle/accelerator position sensor faults based on blink code 06.
Points to accelerator position sensor faults indicated by blink code 08.
Identifies manifold absolute pressure sensor faults indicated by blink code 09.
Indicates engine coolant temperature sensor faults via blink code 12.
Points to intake air temperature sensor faults indicated by blink code 13.
Identifies ambient air pressure sensor faults indicated by blink code 14.
Indicates rollover sensor faults based on blink code 15.
Identifies lambda sensor circuit fault indicated by blink code 17.
Points to system voltage circuit fault indicated by blink code 24.
Indicates side stand switch circuit fault via blink code 25.
Identifies motor drive hall sensor circuit fault indicated by blink code 26.
Points to ignition coil circuit fault indicated by blink code 37.
Identifies fuel pump relay fault indicated by blink code 41.
Indicates lambda sensor heater faults via blink code 45.
Points to fuel evaporation valve faults indicated by blink code 53.
Identifies secondary air valve fault indicated by blink code 54.
Indicates EPT motor drive relay permission signal fault via blink code 58.
Points to motor drive circuit fault indicated by blink code 60.
Identifies throttle position circuit fault indicated by blink code 90.
Indicates CAN bus communication error via blink code 91.
Points to motor drive voltage (internal) circuit fault via blink code 92.
Provides guidelines and warnings for cleaning the motorcycle safely and effectively.
Advises on protecting the motorcycle from road salt and corrosion during winter.
Outlines actions for preparing the motorcycle for long-term storage.
Details steps for bringing the stored motorcycle back into operational condition.
Specifies the engine type, cylinder count, and cooling method.
States the engine's displacement volume in cubic centimeters and cubic inches.
Provides the engine's stroke length in millimeters and inches.
Specifies the engine's bore diameter in millimeters and inches.
Indicates the engine's compression ratio.
Describes the engine's valve control mechanism (OHC, rocker arm, chain drive).
Specifies the diameter of the intake valves.
Specifies the diameter of the exhaust valves.
Provides the specified valve clearance when the engine is cold.
Details the type of bearings used for the crankshaft.
Specifies the type of bearing used for the connecting rod.
Indicates the type of bearing used for the piston pin.
Describes the material and type of pistons used.
Details the types of piston rings fitted to the engine.
Explains the engine's lubrication system (semi-dry sump).
States the ratio of the primary transmission.
Describes the type of clutch used (APTC™ antihopping, hydraulic).
Specifies the gearbox type (6-gears, claw-shifted).
Lists the gear ratios for all six gears.
Details the engine's fuel and air mixture system (electronic fuel injection).
Describes the ignition system type (contactless, fully electronic).
Provides the alternator's voltage and power rating.
Specifies the recommended spark plug model.
Gives the correct gap for the spark plug electrodes.
Describes the engine cooling system (water-cooled, pump circulation).
Lists the components used for starting the engine (electric starter).
Specifies the engine oil capacity and recommended oil types.
Indicates the coolant capacity and recommended coolant types.
Describes the motorcycle's frame construction material and finish.
Specifies the type and model of the front suspension fork.
Details the model and type of the rear shock absorber.
Provides the front and rear suspension travel distances.
Describes the front and rear brake system components.
Lists the diameter of the front and rear brake discs.
Specifies the minimum allowable thickness for brake discs.
Recommended tire air pressures for solo rider.
Recommended tire air pressures for rider and passenger.
States the ratio of the final drive chain.
Specifies the type of drive chain used (X-ring).
Provides the angle measurement for the steering head.
States the distance between the front and rear wheel axles.
Gives the measurement of the seat height without rider or load.
Provides the distance between the ground and the lowest point of the chassis.
Indicates the approximate weight of the motorcycle without fuel.
Specifies the maximum weight allowed on the front axle.
Specifies the maximum weight allowed on the rear axle.
States the maximum total weight the motorcycle can carry.
Lists the battery model, voltage, and capacity.
Provides part numbers and amperage ratings for the motorcycle's fuses.
Details specifications for the motorcycle's lighting components.
Specifies the bulb type and rating for the license plate lamp.
Lists the front and rear tire sizes and models.
Indicates the total fuel tank capacity and reserve.
Gives the specific part number for the front fork assembly.
Specifies the brand and model of the front suspension fork.
Lists recommended settings for fork compression damping.
Provides recommended settings for fork rebound damping.
Specifies the spring length with any preload spacers installed.
Lists the spring rates for different damping settings (soft, medium, hard).
Provides the specified length for the air chamber in the fork.
Gives the total length of the front fork assembly.
Specifies the type and quantity of fork oil required per leg.
Gives the specific part number for the rear shock absorber.
Details the brand and model of the rear shock absorber.
Lists recommended settings for shock absorber high-speed compression damping.
Provides recommended settings for shock absorber low-speed compression damping.
Lists recommended settings for shock absorber rebound damping.
Specifies the recommended spring preload for the shock absorber.
Lists the spring rates for the shock absorber.
Indicates the specified gas pressure for the shock absorber.
Provides the specified static sag measurement for the rear suspension.
States the recommended riding sag measurement for the rear suspension.
Gives the total installed length of the shock absorber.
Specifies the type and part number for shock absorber fluid.
Specifies standards and recommended brands for brake fluid.
Details coolant types, mixture ratios, and recommended brands.
Provides specifications for pre-mixed coolant and its antifreeze rating.
Lists specifications and recommended brands for SAE 10W/60 engine oil.
Details specifications and recommended brands for SAE 10W/50 engine oil.
Specifies the type and recommended brands for fork oil.
Details the specifications and recommended brands for hydraulic fluid.
Specifies the type and recommended brands for shock absorber oil.
States the standard and specification for super unleaded fuel.
Recommends specific Motorex® products for chain cleaning.
Recommends specific Motorex® products for lubricating the chain.
Recommends Motorex® products for cleaning and preserving various materials.
Recommends specific Motorex® products for treating electrical contacts.
Recommends specific Motorex® products for polishing paintwork.
Recommends specific Motorex® products for long-life lubrication.
Recommends specific Motorex® products for cleaning the motorcycle.
Recommends Motorex® products for cleaning and polishing various surfaces.
Recommends specific Motorex® products for universal oil spray applications.
Explains the JASO T903 MA standard for 4-stroke motorcycle engine oils.
Defines SAE viscosity classes for oils and their meaning.
To Next Page