To Next PageTo Next PageWhat to do if my Kuppersberg Hob displays error code ER03?
If your Kuppersberg Hob displays 'ER03', it means that water or a pot is covering the user interface. To resolve this, clean the user interface.
What to do if Kuppersberg ICS 607 Hob displays 'H'?
The 'H' notice indicates a normal high temperature. It will disappear automatically once the temperature decreases.
What to do if my Kuppersberg ICS 607 shows error E3 E?
Error E3 E indicates an abnormal supply voltage that is too high. Inspect whether the power supply is normal, and power on after the power supply is normal.
What does error E4 E mean on my Kuppersberg ICS 607 Hob and how to fix it?
Error E4 E indicates an abnormal supply voltage that is too low. Inspect whether the power supply is normal.
What does E4E mean on my Kuppersberg ICS 607?
The E4E error on your Kuppersberg Hob indicates an abnormal (too low) supply voltage. Please inspect the power supply to ensure it is normal.
What does E2E error mean on Kuppersberg ICS 607 Hob?
The E2E error on your Kuppersberg Hob means the temperature sensor of the IGBT is high. Please restart the hob after it cools down.
Why does my Kuppersberg Hob show E3E error?
The E3E error on your Kuppersberg Hob indicates an abnormal (too high) supply voltage. Inspect the power supply and ensure it is normal before powering on the hob.
What does error F3E mean on my Kuppersberg Hob?
Error F3E indicates a coil temperature sensor failure. The cooking zone indicator will show 'E'. Replace the coil sensor to resolve this issue.
What does it mean when my Kuppersberg Hob displays 'E7'?
The 'E7' error means that the glass surface of the appliance is too hot. You should stop using the appliance and allow it to cool down.
What to do if my Kuppersberg ICS 607 displays ER03 (Induction Hob)?
Error ER03 on your Kuppersberg induction hob indicates water or a pot is on the glass over the control panel. Clean the user interface to fix this.
General| Type | Induction |
|---|---|
| Number of Cooking Zones | 4 |
| Total Power | 7400 W |
| Control Type | Touch |
| Hob Material | Glass Ceramic |
| Weight | 10 kg |
| Voltage | 220-240 V |
| Frequency | 50-60 Hz |
| Height | 55 mm |
| Safety Features | Child Lock, Overheat Protection |
Appliance not for use by persons with reduced capabilities unless supervised.
Appliance and accessible parts become hot during use.
Children under 8 must be kept away unless continuously supervised.
If surface is cracked, switch off to avoid electric shock.
Do not store items on cooking surfaces to prevent fire danger.
Cooking process must be supervised, even for short durations.
Unattended cooking with fat or oil can be dangerous and may result in fire.
If supply cord is damaged, it must be replaced by manufacturer or agent.
Do not use water; switch off and cover flame with lid or blanket.
Use only manufacturer-designed or indicated hob guards.
Overview of models ICS 644, ICS 645 F, ICD 601, ICS 804, ICS 905, ICD 901, ICI 622 W.
Always switch off electricity supply before performing maintenance.
If surface is cracked, disconnect power to avoid electric shock.
Avoid abrasive materials or pan bases that wear markings.
Check correct connection before calling customer service.
Error codes (ER03, H, E, E7) for ceramic hobs and their causes/solutions.
Error codes (U, ER03, F1E) for induction hobs and their causes/solutions.
Error codes (F3E, F4E, E1E, E2E, E3E, E4E, E5E) and their causes/solutions.
Cut work surface to size, ensure 5cm space, 30mm worktop thickness, use heat-resistant material.
Table of installation dimensions (L, W, H, D, A, B, X) for various models.
Check work surface, heat resistance, oven fan, compliance with regulations.
Isolating switch type, accessibility, consult local authorities.
Ensure cable is not pinched, adequate fresh air flow, thermal barrier if above drawer.
Hob must be connected by a qualified person only.
Check wiring system suitability, voltage, and cable capacity.
Check if wiring system is suitable; alterations by electrician only.
Requires a 32 Amp miniature circuit breaker; specific installation rules.
Specs for ECO 411/ECS 403, ECS 627, ICS 607/etc. (Cooking zones, voltage, power, dimensions).
Specs for ECS 630, ICS 804, ICS 905/ICD 901 (Cooking zones, voltage, power, dimensions).
