Why do printouts from the document processor have black lines on my Kyocera All in One Printer?
If printouts from the document processor of your Kyocera All in One Printer have black lines, the slit glass may be dirty. Clean the slit glass.
What to do if pressing Start key doesn't produce copies on Kyocera All in One Printer?
If pressing the Start key on your Kyocera All in One Printer does not produce copies: * Determine the appropriate response to any message displayed and respond accordingly. * Press the Power key to recover the machine from Sleep mode. The machine will be ready to copy within 45 seconds.
Why are printouts from my Kyocera TASKalfa 400ci All in One Printer wrinkled?
Wrinkled printouts from your Kyocera All in One Printer could be due to: * A dirty paper separator of the paper feed unit. Clean the paper separator. * Damp paper. Replace the paper with new paper.
What to do if my Kyocera All in One Printer won't print?
If you cannot print from your Kyocera All in One Printer, ensure the power cord is plugged into an AC outlet and the main power switch is turned on. Verify the printer cable is securely connected, and if the machine was powered on before connecting the cable, power it on again after connecting the cable. If 'Press Status Key...' is displayed, press the Status/Job Cancel key, then [Printing Jobs], and [Resume All Print Jobs].
Why does my Kyocera All in One Printer often jam?
Frequent paper jams in your Kyocera All in One Printer could be due to: * Incorrectly loaded paper. Load the paper correctly. * Unsupported or poor condition paper. Remove the paper, turn it over, and reload it. * Curled, folded, or wrinkled paper. Replace the paper with new paper. * Loose scraps or jammed paper in the machine. Remove any jammed paper.
How to fix dark printouts on my Kyocera TASKalfa 400ci All in One Printer?
If your Kyocera All in One Printer's printouts are too dark: * If the machine is in Auto Density mode, set the correct density level for auto density. * If the machine is in Manual Density mode, use [Image Quality] to set the correct density level.
Why is my Kyocera TASKalfa 400ci All in One Printer ejecting blank sheets?
If your Kyocera All in One Printer is ejecting blank sheets, check the following: * When placing originals on the platen, ensure they are face-down and aligned with the original size indicator plates. * When placing originals in the optional document processor, ensure they are face-up.
What to do if Kyocera TASKalfa 400ci All in One Printer says 'Add toner'?
If your Kyocera All in One Printer displays the message 'Add toner,' replace the toner container.
Why are the printouts from my Kyocera TASKalfa 400ci All in One Printer dirty?
Dirty printouts from your Kyocera All in One Printer may be due to: * A dirty platen or document processor. Clean them. * A dirty transfer roller. Brush the transfer roller clean. * A dirty drum. Carry out Drum Refresh. * Carry out Developer Refresh. * A dirty scanner. Carry out Laser Scanner Cleaning. * The Printed Document Guard Kit being enabled. Disable the Printed Document Guard Kit.
How to fix light printouts on my Kyocera All in One Printer?
If your Kyocera All in One Printer's printouts are too light, consider the following: * If the machine is in Auto Density mode, set the correct density level for auto density. * If the machine is in Manual Density mode, use [Image Quality] to set the correct density level. * Shake the toner container from side to side several times to evenly distribute the toner. * If there is a message indicating the addition of toner, replace the toner container. * If the paper is damp, replace it with new paper. * Carry out Drum Refresh. * Carry out Developer Refresh. * Carry out Laser Scanner Cleaning. * If EcoPrint mode is enabled, disable it.
General| Brand | Kyocera |
|---|---|
| Model | TASKalfa 400ci |
| Category | All in One Printer |
| Language | English |
To Next Page
