lancer IBD 30 - User Manual

Other manuals for lancer IBD 30

Installation Guide12 pages

Questions and Answers

A
Amanda WallSep 10, 2025
Why is the BIB pump operating, but there is no syrup flow in my lancer IBD 30 Dispenser?
- K
  Katherine BooneSep 12, 2025
  If the BIB pump is running, but there's no syrup flow in your lancer Dispenser, it could be due to: * Leak in syrup inlet or outlet line: Replace the line. * Defective BIB pump: Replace the BIB pump.
S
Sherry ReynoldsSep 9, 2025
Why is my lancer Dispenser not dispensing ice, or dispensing poor quality ice?
- N
  normanfloydSep 9, 2025
  If the ice door opens, the motor runs, but no ice dispenses (or the ice is of poor quality) from your lancer Dispenser, consider these possibilities: * Dispenser is out of ice: Fill the dispenser with ice. * Agitator pin is missing or damaged: Replace the agitator pin. * Poor ice quality: Service the ice machine. * Key not installed on agitation shaft: Install the key on the agitation shaft.
C
Christopher HolderSep 8, 2025
Why does the motor run but the ice door doesn't open on my lancer IBD 30 Dispenser?
- M
  Mr. William GalvanSep 8, 2025
  If the motor runs but the ice door doesn't open when using the push chute on your lancer Dispenser, check these potential issues: * Solenoid not connected to PC board: Connect the solenoid to the PC board. * Solenoid defective: Replace the solenoid. * PC board defective: Replace the PC board.
A
Amanda DominguezAug 22, 2025
What to do if the lancer Dispenser has no power when activated?
- A
  austinkhanAug 23, 2025
  If your lancer Dispenser doesn't power on when activated (and the switch panel isn't lit), there are several possible causes: * A malfunctioning switch assembly: Consider replacing the switch assembly. * No power to the dispenser: Check the internal breaker and incoming power. * A malfunctioning power supply: Check the voltage to the power supply and inspect the fuses. * A malfunctioning PCB board: Replacement of the PCB board may be necessary.
T
Trevor HermanSep 5, 2025
What to do if the ice door opens but the motor doesn't run on my lancer IBD 30?
- G
  goodwinoliviaSep 5, 2025
  If the ice door opens when you use the push chute on your lancer Dispenser, but the motor doesn't run, consider these potential problems: * Wiring harness not plugged in: Plug in the wiring harness. * PC board defective: Replace the PC board. * Motor defective: Replace the motor.
C
Christian McdonaldSep 4, 2025
Why does my lancer IBD 30 Dispenser have an erratic ratio?
- M
  Matthew MerrittSep 4, 2025
  An erratic ratio in your lancer Dispenser could be due to: * Incoming water and/or syrup supply not at minimum flowing pressure: Check pressure and adjust. * Foreign debris in water and/or syrup flow control: Remove flow control from suspected valve and clean out any foreign material to ensure smooth spool movement. * CO regulator malfunction: Repair or replace CO regulator.
J
Julie MorrisonSep 3, 2025
What to do if the lancer IBD 30 push chute has no response?
- R
  Ricky GomezSep 3, 2025
  If the push chute on your lancer Dispenser isn't responding, check these potential causes: * Dispenser not connected to power source: Connect the dispenser to a power source. * Wiring harness not plugged in: Plug in the wiring harness. * PC board defective: Replace the PC board. * Malfunctioning power supply: Check the voltage to the power supply and check the fuses.
H
hjohnsonSep 2, 2025
Why is my lancer IBD 30 dispensing syrup and CO gas, but no water?
- T
  Tracy OlsonSep 2, 2025
  If your lancer Dispenser is dispensing syrup and CO gas, but no water, consider the following possible causes: * Improper water flow to dispenser: Check for water flow to dispenser. * Carbonator pump motor has timed out: Reset by turning the unit OFF, then ON by using the circuit breaker on the power supply or momentarily unplugging unit. * Liquid level probe not connected properly to PCB: Check connections of liquid level probe to PCB assembly. * Defective PCB assembly: Replace PCB assembly. * Defective liquid level probe: Replace liquid level probe. * Weak or defective carbonator pump: Replace pump.
R
Robert TranSep 1, 2025
What causes the circuit breaker to trip on my lancer IBD 30?
- R
  rebecca85Sep 1, 2025
  If the circuit breaker is tripping on your lancer Dispenser, try these troubleshooting steps: * Valve wire harness shorted to itself or faucet plate: Detect short by disconnecting valve harnesses from switch panel (4 25-pin harnesses and 4 9-pin harnesses). Restore power. If breaker does not trip, find and replace shorted harness. * Controller PCB is bad: Detect by disconnecting the white 5-pin harness from the controller PCB. Restore power. If breaker does not trip, replace controller PCB. * Secondary wire harness has a short: Locate short from a motor or solenoid harness and replace. * Power supply is bad: Detect short by disconnecting all harnesses connected to power supply. Restore power. If breaker still trips, replace power supply.
B
Brittany DavisAug 30, 2025
Why is my lancer IBD 30 Dispenser dispensing only water or only syrup?
- M
  Michele HopkinsAug 31, 2025
  If your lancer Dispenser is dispensing only water or only syrup, here are some potential causes: * Syrup BIB empty: Replace the syrup BIB as required. * Water or syrup shutoff on mounting block not fully open: Open shutoff completely. * Improper or inadequate water or syrup supply: Remove valve from mounting block & open shutoffs slightly. Check water & syrup supply. If no supply, check unit for other problems. Ensure BIB connection is engaged. * CO pressure to syrup pump too low: Check the CO pressure to the pump to ensure it is between 70-80 PSI (0.483-0.552 MPA). * Stalled or inoperative BIB pump: Check CO pressure and/or replace pump. * Kinked line: Remove kink or replace line. * CO regulator malfunction: Repair or replace CO regulator as required.