Lantronix UDS1100

Lantronix UDS1100

86 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

3: Getting Started

4. Enter the new IP address, subnet mask, and gateway (if applicable).

5. Do one of the following:

 Continue with 5: Configuration via Telnet or Serial Port (Setup Mode.

 Select 9 to save and exit Setup Mode. The unit performs a power reset.

UDS1100 User Guide 22

Table of Contents

Default Chapter3
- Table of Contents3
- Figures6
1 : Using this Guide8
- Purpose and Audience8
- Chapter Summary8
- Additional Documentation9
2 : Introduction10
- Applications10
- Application Examples10
- Figure 2-1. Serial Tunneling Example11
- Figure 2-2. Direct TCP/IP or Redirector Configuration11
- Protocol Support12
- Additional Features12
- Configuration Methods12
- Product Information Label13
- Figure 2-3. Sample Hardware Address13
3 : Getting Started14
- Package Contents14
- Installing the UDS15
- Figure 3-1. UDS1100-POE Version Connected to Serial Device and Network15
- Figure 3-2. Standard UDS1100 Connected to Serial Device and Network16
- Required Information17
  - Hardware Address17
  - IP Address17
- Assigning the IP Address: Deviceinstaller18
- Assigning the IP Address: Serial Port Login21
4 : Configuration Using Web-Manager23
- Accessing UDS1100 Using Deviceinstaller23
- Network Configuration24
- Server Configuration27
- Figure 4-4. Server Settings27
- Host List Configuration28
- Channel 1 Configuration29
- Apply Settings36
- Apply Factory Defaults36
5 : Configuration Via Telnet or Serial Port (Setup Mode)37
- Accessing Setup Mode37
  - Telnet Connection37
  - Serial Port Connection38
- Exiting Setup Mode38
- Figure 5-1. MAC Address38
- Figure 5-2. Setup Menu Options38
6 : Setup Mode: Server Configuration39
- Server Configuration (Option 0)39
- IP Address39
- Set Gateway IP Address39
- Figure 6-1. Network Settings39
- Table 6-1. Bootp/Dhcp/Autoip Options39
- Netmask: Number of Bits for Host Part40
- Set DNS Server IP Address40
- Change Telnet Configuration Password40
- Table 6-2. Standard IP Network Netmasks40
- DHCP Name41
7 : Setup Mode: Channel Configuration42
- Channel 1 (Option 1)42
- Baudrate42
- Figure 7-1. Serial Port Settings42
- I/F (Interface) Mode43
- Flow43
- Figure 7-2. Interface Mode43
- Table 7-1. Interface Mode Options43
- Table 7-2. Common Interface Mode Settings43
- Port Number44
- Connect Mode44
  - Table 7-3. Flow Control Options44
  - Table 7-4. Reserved Port Numbers44
  - A) Incoming Connection45
  - Table 7-5. Connect Mode Options45
  - B) Response46
  - C) Active Startup46
  - Figure 7-3. Manual Connection Address Example47
  - D) Datagram Type48
  - E) Modem Mode48
  - Table 7-6. Modem Mode Commands50
- Send the Escape Sequence (+++) in Modem Mode51
- Show IP Addr after 'RING51
- Auto Increment Source Port51
- Remote IP Address51
- Remote Port52
- Disconnmode52
- Table 7-7. Disconnect Mode Options52
- Flush Mode (Buffer Flushing)53
- Pack Control53
  - Table 7-8. Flush Mode Options53
  - Table 7-9. Pack Control Options53
  - Packing Interval54
  - Send Characters54
  - Trailing Characters54
- Disconntime (Inactivity Timeout)54
- Telnet Terminal Type55
- Channel (Port) Password55
8 : Setup Mode: Advanced Settings56
- Expert Settings (Option 5)56
- Security Settings (Option 6)57
- Default Settings (Option 7)59
9 : Firmware Upgrades61
- Obtaining Firmware61
- Reloading Firmware61
10 : Monitor Mode64
- Entering Monitor Mode Using the Serial Port64
- Entering Monitor Mode Using the Network Port64
- Monitor Mode Commands64
- Table 10-1. Monitor Mode Commands65
11 : Troubleshooting and Contact Information67
- Leds67
- Problems and Error Messages68
- Technical Support70
12 : Connections and Pinouts71
- Serial Port71
- Serial Connector Pinouts71
- Figure 12-1. Serial Interface71
- Figure 12-2. DB25 Female DCE Interface RS23271
- Modem Cable72
- Figure 12-3. DB25 Female Interface RS422 (4 Wire Mode)72
- Figure 12-4. DB25 Female Interface RS485 (2 Wire Mode)72
- Network Port73
- Figure 12-5. Wiring Diagram for Lantronix Modem Cable, Part No. 500-16373
- Ethernet Connector Pinouts74
- Power Plug74
13 : Technical Specifications75
A: Mounting Brackets77
B: Alternative Ways to Assign an IP Address78
- Dhcp78
- Autoip78
- Bootp79
- ARP and Telnet79
C: Binary to Hexadecimal Conversions80
- Converting Binary to Hexadecimal80
  - Conversion Table80
  - Scientific Calculator81
D: Warranty82
E: Compliance and Disclaimer83
- Rohs Notice84
Index85

Other manuals for Lantronix UDS1100

Programming Guide7 pages

Quick Start Guide12 pages

Related product manuals

Lantronix UBOX4100

Preview: Lantronix MSS4

Preview: Lantronix XPort

Lantronix XPort

Preview: Lantronix EDS8PS

Lantronix EDS8PS

Preview: Lantronix SCS100

Lantronix SCS100

Preview: Lantronix EDS2100

Lantronix EDS2100

Preview: Lantronix EDS32PR

Lantronix EDS32PR

Preview: Lantronix MatchPort

Lantronix MatchPort

Preview: Lantronix CoBox-Micro

Lantronix CoBox-Micro

Preview: Lantronix PremierWave XN

Lantronix PremierWave XN

Preview: Lantronix DSTni-XPress DR

Lantronix DSTni-XPress DR

Lantronix Device Installer