Lenze E84DGFCp Series User Manual

EDS84DMOTPBUS EN 3.0 - 11/2011 L 97
Communication manual 8400 motec PROFIBUS
Index
15 Index
A
Abort of data transfer by the controller (DP-V0) 45
Access to process data 35
Active station address (C13864) 84
Acyclic data transfer (DP-V1) 53
Addressing of Lenze parameters/parameter data 41
All words from master (C13851) 82
All words from standard device (C13853) 83
All words to master (C13850) 82
All words to standard device (C13852) 82
Analog input information 40
Application as directed 14
Application notes (representation) 11
Application of the communication unit 14
Approvals 18
B
Baud rate 18
Baud rate (C13863) 84
Before initial switch-on 28
Bus cable length 25
Bus counter (C13862) 84
Bus status (C13861) 83
Bus termination 18, 24
C
C01501 | Resp. to communication error with MCI 81
C01503 | MCI timeout 81
C13850 | All words to master 82
C13851 | All words from master 82
C13852 | All words to standard device 82
C13853 | All words from standard device 83
C13860 | Settings 83
C13861 | Bus status 83
C13862 | Bus counter 84
C13863 | Baud rate 84
C13864 | Active station address 84
C13865 | Display:Most recent PRM data 84
C13866 | Display:Most recent CFG data 85
C13867 | Display: Most recent diagnostic data 85
C13880 | Reaction on communication failure 85
C13881 | Monitoring time: Data exchange 85
C13882 | Monitoring time: Watchdog 86
C13885 | Delete process data 86
C13886 | Set ext. diagnostic bit in case of 86
C13887 | Suppress signalling diag. mess. upon 87
C13899 | Station address 87
C13900 | Firmware product type 87
C13901 | Firmware compilation date 87
C13902 | Firmware version 87
C13920 | Display: DIP switch setting 88
C13950 | Module internal communication status 88
Cable length 18
Codes 81
Commissioning 28
Communication channels 34
Communication medium 18
Communication profile 18
Communication time 19
Communication-relevant parameters of the operating
system
81
Configuration for the host (master) 29
Configuration of the master 29
Configuring the host (master) 29
Configuring the port interconnection in the
»Engineer«
36
Conformities 18
Connection establishment between master and slave
(DP-V1)
52
Conventions 9
Conventions used 9
Copyright 2
D
Data transfer 34
Data transfer abort by the master (DP-V0) 45
Delete process data (C13885) 86
Device- and application-specific safety instructions 13
Device data base file 29, 30
Device protection 13
Diagnostic data 75
Diagnostic message 75
Diagnostic messages 75
Diagnostics 72
Diagnostics with the »Engineer« 73
Digital input information 40
DIP switch positions for setting the station address 93
DIP switch settings 30, 31, 93
Display
DIP switch setting (C13920)
88
Most recent CFG data (C13866) 85
Most recent diagnostic data (C13867) 85
Most recent PRM data (C13865) 84
Document history 8
DP-V0 42
DP-V1 51
DRIVECOM 42
DRIVECOM parameter data channel (DP-V0) 42
E
Electrical installation 22
Error:Lenze settings loaded (error message) 79
Error code of the Inverter Drive 8400 76

Lenze E84DGFCp Series Specifications

General

Brand	Lenze
Model	E84DGFCp Series
Category	Conference System
Language	English