Why does Lippert Components Level-Up show 'PANIC STOP Function Aborted'?
The 'PANIC STOP Function Aborted' message on Lippert Components Lifting Systems indicates that a button was pressed on the touch pad during an automatic operation. Restart the automatic operation and refrain from pressing any buttons on the touch pad.
What does 'Feature Disabled' mean on Lippert Components Level-Up Lifting Systems and how to fix it?
The 'Feature Disabled' error on Lippert Components Lifting Systems can occur if the front of the coach is below level when starting the Auto Level process. Raise the front of the coach above level and restart the Auto Level process. This error can also appear if the touch pad power is not cycled between consecutive leveling operations; turn the touch pad off and then back on to reset the system. Finally, this can indicate that the zero point has not been set, in which case set the zero point.
What does 'Bad Calibration' mean on Lippert Components Level-Up Lifting Systems?
If the Lippert Components Lifting Systems display a 'Bad Calibration' error, it means the sensor calibration values are out of range. Replace the controller.
What does 'Internal Sensor' error mean on Lippert Components Level-Up Lifting Systems and how to resolve it?
If the Lippert Components Lifting Systems display an 'Internal Sensor' error, it indicates an internal sensor problem. Replace the controller.
What does 'External Sensor' error mean on Lippert Components Level-Up?
If the Lippert Components Lifting Systems display an 'External Sensor' error, it indicates a bad connection or wiring from the controller to the rear sensor. Replace or repair the connection to the rear remote sensor.
What causes 'EXCESS ANGLE' on Lippert Components Level-Up Lifting Systems?
If your Lippert Components Lifting Systems displays 'EXCESS ANGLE', it means an excessive angle was reached during operation. This can happen during either auto or manual operation. To resolve this, relocate the 5th Wheel and ensure the controller is properly secured.
What to do if Lippert Components Lifting Systems shows 'Auto Level Fail' error?
If your Lippert Components Lifting Systems displays an 'Auto Level Fail' error, it could be due to uneven ground or an incorrectly set zero point. Check the position of the jacks and consider relocating the trailer to more level ground. If the ground isn't the issue, reset the zero point.
What to do if Lippert Components Level-Up Lifting Systems displays 'Out Of Stroke' error?
If your Lippert Components Lifting Systems displays an 'Out Of Stroke' error, it means the jack has reached its maximum stroke length and can't lift any further. Check the disposition of the jacks and/or relocate the trailer.
What to do if Lippert Components Level-Up Lifting Systems displays 'Jack Time Out' error?
If your Lippert Components Lifting Systems displays a 'Jack Time Out' error, it means the time limit for the requested auto operation has been exceeded. Check the disposition of the jacks.
What to do if Lippert Components Level-Up Lifting Systems shows 'Feature Disabled' error?
If your Lippert Components Lifting Systems displays a 'Feature Disabled' error, the cause could be one of several things. * If you're trying to initiate Hitch Recognition, the front of the trailer may be below level. Push the “FRONT” button to raise the trailer to hitch height. * The touch pad power may not have been cycled between leveling operations. Turn the touch pad off and then back on to reset the system. * The zero point may not be set. Set the zero point.
Conditions and steps required before operating the leveling system.
Details on recommended hydraulic fluid type and usage.
Schedule and steps for routine system maintenance.
Guidance on choosing a suitable location for leveling.
Step-by-step instructions for automatic leveling.
Diagrams of leveling jacks, footpads, and associated components.
Diagrams of the hydraulic power unit and its key parts.
Diagrams of controller, touch pad, sensors, and harnesses.
General| System Type | Automatic Hydraulic |
|---|---|
| Category | Lifting Systems |
| Number of Jacks | 4 or 6 |
| Auto-Leveling | Yes |
| Manual Override | Yes |
| Power Source | 12V DC |
| Control Type | Electronic |
| Installation Type | Frame-mounted |
To Next Page
