What to do if Lippert Components Lifting Systems displays 'Excess Angle' error?
If your Lippert Components Lifting Systems displays an 'Excess Angle' error, it means an excessive angle was reached during operation. This can happen in auto or manual mode. Check and secure the controller placement. You may need to relocate the trailer.
What to do if Lippert Components Level-Up Lifting Systems displays 'External Sensor' error?
If your Lippert Components Lifting Systems displays an 'External Sensor' error, it indicates a bad connection or wiring from the controller to the rear sensor. Replace or repair the connection to the rear remote sensor.
What to do if Lippert Components Level-Up Lifting Systems displays 'Bad Calibration' error?
If your Lippert Components Lifting Systems displays a 'Bad Calibration' error, it means the sensor calibration values are out of range. Replace the controller.
What to do if Lippert Components Level-Up Lifting Systems displays 'Internal Sensor' error?
If your Lippert Components Lifting Systems displays an 'Internal Sensor' error, it indicates an internal sensor problem. Replace the controller.
Why Lippert Components Lifting Systems shows 'Panic Stop Function Aborted'?
The 'Panic Stop Function Aborted' error on your Lippert Components Lifting Systems means a button was pressed on the touch pad during an automatic operation. Restart the automatic operation and refrain from pressing any buttons on the touch pad.
Why does my Lippert Components Lifting Systems show 'FEATURE DISABLED'?
The 'FEATURE DISABLED' message on your Lippert Components Lifting Systems typically indicates one of three issues. First, the front of your 5th Wheel might be below level when starting the auto-level process, especially when initiating Hitch Recognition. To resolve this, use the FRONT button to raise the 5th Wheel to hitch height before connecting to your tow vehicle. Second, the touchpad power may not have been cycled between consecutive leveling operations. To fix this, turn the touchpad off and then back on to reset the system. Third, the Zero Point might not be set. In this case, you'll need to set the Zero Point.
What to do if Lippert Components Level-Up Lifting Systems shows 'LOW VOLTAGE'?
If your Lippert Components Lifting Systems displays 'LOW VOLTAGE', it means the battery voltage has dropped below 9.5V. You should check the wiring for any damage and repair or replace as needed. Also, test the battery voltage under load and charge or replace the battery if necessary.
Why does my Lippert Components Level-Up Lifting Systems say 'AUTO LEVEL FAIL'?
The 'AUTO LEVEL FAIL' message on your Lippert Components Lifting Systems indicates that the system was unable to auto-level. This could be due to uneven ground, so check the disposition of the jacks and/or relocate the 5th Wheel. Alternatively, the Zero Point may be set incorrectly; in this case, you should reset the zero point.
What to do if Lippert Components Lifting Systems displays 'Low Voltage' error?
If your Lippert Components Lifting Systems displays a 'Low Voltage' error, it means the battery voltage has dropped below 9.5V. First, check the wiring and repair or replace if necessary. If the wiring is fine, test the battery voltage under load and either charge or replace the battery.
What does 'OUT OF STROKE' mean on Lippert Components Level-Up?
If your Lippert Components Lifting Systems displays 'OUT OF STROKE', it means the jack has reached its maximum stroke length and is unable to lift further. To resolve this, check the disposition of the jacks and/or relocate the 5th Wheel.
Conditions and steps required before operating the leveling system.
Details on recommended hydraulic fluid type and usage.
Schedule and steps for routine system maintenance.
Guidance on choosing a suitable location for leveling.
Step-by-step instructions for automatic leveling.
Diagrams of leveling jacks, footpads, and associated components.
Diagrams of the hydraulic power unit and its key parts.
Diagrams of controller, touch pad, sensors, and harnesses.
General| System Type | Automatic Hydraulic |
|---|---|
| Category | Lifting Systems |
| Number of Jacks | 4 or 6 |
| Auto-Leveling | Yes |
| Manual Override | Yes |
| Power Source | 12V DC |
| Control Type | Electronic |
| Installation Type | Frame-mounted |
To Next Page
