Lowara e-SVE - User Manual

Questions and Answers

B
Brandy ValdezSep 10, 2025
What to do if the pressure is below the minimum threshold in my Lowara e-SVE?
- H
  haydenjamesSep 10, 2025
  If the pressure is below the minimum threshold in your Lowara Water Pump (not present in ACT mode), check the settings of parameters P45 and P46.
P
pjohnsonAug 23, 2025
What to do if my Lowara e-SVE shows error A20?
- D
  dmayAug 23, 2025
  Stop the pump for 5 minutes and then restart it again; if the problem continues, contact Xylem or the Authorised Distributor.
B
Barry JonesAug 25, 2025
What to do if my Lowara e-SVE shows a high motor current?
- J
  James HenryAug 25, 2025
  If your Lowara Water Pump displays a high motor current, stop the pump for 5 minutes and then restart it. If the problem continues, it is recommended to contact Xylem or the Authorised Distributor.
W
Wendy WilsonAug 26, 2025
Why is my Lowara e-SVE motor overheating?
- K
  Kelly CurtisAug 27, 2025
  A motor thermal protection trip in your Lowara Water Pump can occur due to several reasons: * Impurities near the impeller and rotor. * Installation conditions and water/air temperature issues. Check for and remove any impurities. Verify the installation conditions and temperatures. Allow the motor to cool down. If the error persists, stop the pump for 5 minutes, restart it, and if it still continues, contact Xylem or the Authorised Distributor.
S
Shane BrownAug 28, 2025
What should I do if my Lowara Water Pump voltage supply is out of operating range?
- A
  Angela McdonaldAug 28, 2025
  If your Lowara Water Pump's voltage supply is out of the operating range, check the voltage and the connection of the electric system.
M
mjohnsonAug 29, 2025
What to do if one of the power supply phases is missing in my Lowara e-SVE?
- D
  David SmithAug 29, 2025
  If one of the three power supply phases is missing in your Lowara Water Pump (three-phase versions only), check the connection to the power supply network.
A
Alyssa ColemanSep 18, 2025
What to do if my Lowara e-SVE Water Pump has a hardware error?
- T
  Teresa LeonardSep 18, 2025
  If your Lowara Water Pump has a hardware error, stop the pump for 5 minutes and then restart it again. If the problem continues, contact Xylem or the Authorised Distributor.
K
Kevin CruzSep 12, 2025
What causes corrupted multi-pump connection in Lowara Water Pump and how to solve it?
- Z
  zmillerSep 12, 2025
  A corrupted multi-pump connection in your Lowara Water Pump could be due to: * The condition of the connection cables. * Address discrepancies. Check the condition of the connection cables and ensure there are no address discrepancies.
E
Elizabeth BakerSep 8, 2025
What to do if the pressure sensor is missing on my Lowara e-SVE?
- S
  Scott HudsonSep 8, 2025
  If the pressure sensor is missing on your Lowara Water Pump (not present in ACT mode), check the condition of the sensor connection cables.
B
Brandon OneillSep 5, 2025
What to check if the frequency converter thermal protection trips on my Lowara e-SVE Water Pump?
- C
  Charles YangSep 5, 2025
  If the frequency converter thermal protection trips on your Lowara Water Pump, check the conditions of installation and the air temperature.