Grindomatic
2 Grindomatic 201708 EN
Table of Contents
1 Introduction . . . . . . . . . . . . . 3
1.1 Important user information . . . . . . .3
1.2 About this manual . . . . . . . . . . . .3
1.3 Intended use . . . . . . . . . . . . . .3
1.4 Regulatory information . . . . . . . . .3
1.5 Nameplate. . . . . . . . . . . . . . . .4
1.6 Recycling information . . . . . . . . . .4
2 Safety . . . . . . . . . . . . . . . . 5
2.1 Safety notices . . . . . . . . . . . . . .5
2.2 Safety instructions. . . . . . . . . . . .5
2.3 Signs and symbols . . . . . . . . . . .6
3 Product Description . . . . . . . . . 7
3.1 Product overview . . . . . . . . . . . .7
3.2 Front view . . . . . . . . . . . . . . . .7
3.3 Back view . . . . . . . . . . . . . . . .8
3.4 Grinding head . . . . . . . . . . . . .9
3.5 Controls . . . . . . . . . . . . . . . . 10
3.5.1 Grinding speed knob . . . . . 11
3.6 Chain overview . . . . . . . . . . . . 11
3.7 Technical data. . . . . . . . . . . . .12
4 Installation . . . . . . . . . . . . . 13
4.1 Safety during installation . . . . . . . 13
4.2 Site requirements . . . . . . . . . . . 13
4.3 Unpacking the machine . . . . . . . .13
4.4 Bench-mounting the machine . . . . .14
4.5 Installing the grinding wheel. . . . . .14
4.6 Test the machine before first use . . . 16
5 Operation . . . . . . . . . . . . . 17
5.1 Safety during operation . . . . . . . . 17
5.2 Preparing for operation . . . . . . . . 17
5.2.1 Preparing the grinding wheel . 17
5.2.2 Setting the head-tilt angle. . .18
5.2.3 Setting the top-plate angle . .18
5.2.4 Inserting the chain . . . . . . 19
5.2.5 Making the grinding settings . 20
5.3 Operating the machine . . . . . . . . 23
5.4 Depth gauge grinding . . . . . . . . . 24
© 2017 Markusson Professional Grinders AB - All rights reserved.
6 Maintenance and Service . . . . . 26
6.1 Safety during maintenance . . . . . . 26
6.2 Frequency of maintenance . . . . . . 26
6.3 Changing the grinding wheel and fitting
the grinding wheel guard . . . . . . . 27
6.4 Fastening the chain vise . . . . . . . 28
6.5 Checking and adjusting the wire . . . 28
6.6 Service . . . . . . . . . . . . . . . . 29
7 Troubleshooting . . . . . . . . . . 30
7.1 Troubleshooting procedure . . . . . . 30
7.2 Sharpening test . . . . . . . . . . . . 30
7.3 Issues . . . . . . . . . . . . . . . . . 31
8 Accessories and Spare Parts . . . 32
8.1 Ordering information . . . . . . . . . 32
8.2 List of accessories. . . . . . . . . . .
. . . . . . . . . . . . . . . . . . 32
8.3 Spare parts . . . . . . . . . . . . . . 33
8.4 Converter . . . . . . . . . . . . . . .35
8.5 Stand . . . . . . . . . . . . . . . . . 35
8.6 Pneumatic chain tensioner . . . . . . 36
9 Assembling the stand . . . . . . . 37
9.1 Assembling the pneumatic chain
tensioner . . . . . . . . . . . . . . . 38
9.2 Using the chain tensioner . . . . . . .41
10 Declaration of conformity . . . . . 43
To Next Page
Loading...
