EasyManua.ls Logo

Martin MAC 600 - User Manual

Martin MAC 600
28 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
MAC 600/E
user manual
© 1997 - 2000 Martin Professional A/S, Denmark.
All rights reserved. No part of this manual may be
reproduced, in any form or by any means, without
permission in writing from Martin Professional A/S,
Denmark.
Printed in Denmark.
P/N 35000018 Rev. G
section 1
INTRODUCTION
About this manual .................................................................................................................................................... 4
Safety precautions ................................................................................................................................................... 4
section 2
SETUP
Unpacking................................................................................................................................................................ 5
Installing or changing the lamp ................................................................................................................................ 5
Powering the fixture ................................................................................................................................................. 5

Table of Contents

Questions and Answers

  • C
    cbestAug 18, 2025
    How to troubleshoot a completely dead Martin MAC 600 fixture?
    • V
      vincentbowenAug 18, 2025
      If one or more Martin Lighting Equipment fixtures are completely dead, first ensure the power is switched on and all cables are properly connected. If the fixture still doesn't power on, disconnect it and check the primary fuse located at the mains inlet cable and replace it if blown. Also, check the secondary fuses (F601 and F602) on the PCB inside the fixture base and replace them if necessary.
  • D
    derrickyoungAug 22, 2025
    Why does the lamp fail to strike on my Martin MAC 600 Lighting Equipment?
    • T
      Tabitha FosterAug 23, 2025
      If the lamp fails to strike on your Martin Lighting Equipment (with “LERR” displayed on MAC 600), the ballast and transformer settings might not match the local AC voltage and frequency. Disconnect the fixture and check these settings, correcting them if necessary. The lamp itself may also be blown and needs replacing after disconnecting the fixture. Ensure the lamp is installed correctly. If the lamp is too hot, allow it to cool, then execute a lamp-off followed by a lamp-on command.
  • K
    Kimberly Phillips DDSAug 26, 2025
    Why all Martin MAC 600 fixtures respond erratically to the controller?
    • C
      Calvin MooreAug 26, 2025
      If all Martin Lighting Equipment fixtures respond erratically after resetting, the controller may be disconnected from the data link; ensure the controller is properly connected. Also, the XLR pin-out of the controller might not match the pin-out of the first fixture. In this case, install a phase-reversing cable between the controller and the first fixture.
  • R
    Rachael RuizAug 27, 2025
    What to do if the lamp cuts out intermittently on Martin MAC 600 Lighting Equipment?
    • D
      Douglas Vargas MDAug 27, 2025
      If the lamp on your Martin Lighting Equipment cuts out intermittently, the fixture may be overheating. Allow the fixture to cool, reduce the ambient room temperature, and set the fan speed to full. You might also need to recalibrate the temperature sensors. Another potential cause is that the ballast and transformer settings do not match the local AC voltage and frequency. Disconnect the fixture and check these settings, correcting them if necessary.
  • C
    charles21Aug 30, 2025
    Why is the light output low on my Martin MAC 600?
    • D
      Dylan OchoaAug 30, 2025
      If your Martin Lighting Equipment has low light output, the lamp might be near the end of its life; try replacing it. Also, the ballast and transformer settings might not match the local AC voltage and frequency; disconnect the fixture and check/correct these settings. If you are using a MAC 600 E, ensure the correct ballast type is selected by checking the S/N and setting the ballast type personality accordingly. Finally, the lamp may be misaligned, so adjust it as needed.
  • K
    Kenneth MolinaSep 1, 2025
    What to do if my Martin DJ Equipment shows 'LERR' and no light?
    • L
      latoyarodriguezSep 2, 2025
      If your Martin DJ Equipment fixture isn't lighting up and shows a 'LERR' error, it could be due to a few reasons. First, the ballast and transformer settings might not be correct for your local AC voltage and frequency; in this case, disconnect the fixture and check these settings, correcting them if needed. Another cause could be a blown lamp, so disconnect the fixture and replace the lamp. Finally, ensure the lamp is installed correctly by disconnecting the fixture and installing the lamp.
  • A
    Alan WilsonSep 7, 2025
    Why all Martin DJ Equipment fixtures respond erratically to the controller?
    • L
      lewissharonSep 7, 2025
      If Martin DJ Equipment fixtures reset correctly but all respond erratically or not at all to the controller, it could be because the controller is disconnected from the data link; connect the controller. Also, the XLR pin-out of the controller might not match the pin-out of the first fixture, meaning the signal is reversed; install a phase-reversing cable between the controller and the first fixture on the link.
  • S
    Shelly KennedySep 9, 2025
    How to troubleshoot a completely dead Martin DJ Equipment fixture?
    • M
      Mark PowellSep 9, 2025
      If one or more of your Martin DJ Equipment fixtures is completely dead, first check that the power is switched on and the cables are plugged in. If that's not the issue, the primary fuse (located at the mains inlet cable) may be blown; disconnect the fixture and replace the fuse. Alternatively, secondary fuses (located on the PCB inside the fixture base) might be blown; disconnect the fixture, check the fuses on the PCB (F601 and F602), and replace them if necessary.
  • T
    Teresa JacobsSep 12, 2025
    Why does the lamp in my Martin DJ Equipment cut out intermittently?
    • C
      cmartinezSep 12, 2025
      If your Martin DJ Equipment lamp cuts out intermittently, the fixture may be too hot. Allow the fixture to cool, reduce the ambient room temperature, set the fan speed to full, and recalibrate the temperature sensors. Also, the ballast and transformer settings may not match your local AC voltage and frequency. Disconnect the fixture and check and correct these settings if needed.
  • B
    Brandon FergusonSep 14, 2025
    What causes low light output in Martin DJ Equipment?
    • K
      kathrynrodriguezSep 14, 2025
      If your Martin DJ Equipment has low light output, the lamp may be near the end of its life. Replace the lamp.

Summary

INTRODUCTION

About this manual

Covers manual content, software versions, and where to find updates.

Safety precautions

Details risks (shock, UV, fire, falls) and necessary precautions for safe operation.

SETUP

Unpacking

Lists package contents and emphasizes using original packing for transport.

Installing or changing the lamp

Step-by-step guide for safely installing or replacing the fixture's lamp.

Powering the fixture

Covers checking voltage/frequency settings and grounding for safe AC power connection.

Rigging the fixture in place

Instructions for safely mounting the fixture on a truss or stage using clamps and safety cables.

Connecting the serial link

Tips for building a reliable RS-485 serial link, cable types, and termination.

Connecting fixtures

Explains connecting multiple fixtures via XLR and DMX/Martin protocols, including cable types.

Setting control protocol and address

Guides on selecting DMX/Martin protocol and assigning start addresses for fixture control.

Installing the snoot (optional)

Instructions for attaching the optional snoot accessory to the fixture.

OPERATION

Martin RS-485 control

Details controlling the fixture using Martin RS-485 protocol and compatible controllers.

DMX-512 control

Explains DMX control modes (tracking, vector) and resolution settings.

Lamp

Covers automatic lamp-on, DMX lamp-off, and reduced power mode for lamp operation.

Mechanical effects

Describes pan, tilt, color wheel, CMY mixing, beam shapers, dimmer, and shutter effects.

CONTROL MODULE

Address and protocol selection

How to set the DMX or Martin address and select the control protocol using the control panel.

Personality settings

Details various personality settings for customizing fixture behavior like speed, feedback, and display.

Readouts

Explains how to access usage, DMX values, software version, and temperature readouts.

Manual control

Describes manual operation of fixture functions like reset, lamp, shutter, dimmer, and effects.

Test sequences

Outlines running general tests, circuit board tests, and factory tests for diagnostics.

Utilities

Covers calibration, resetting defaults, and saving custom configurations for the fixture.

MAINTENANCE AND BASIC SERVICE OPERATIONS

Removing the printed circuit board

Step-by-step guide to safely remove the printed circuit board from the fixture.

Replacing the printed circuit board

Instructions for reinserting the circuit board and reconnecting wire connectors.

Replacing fuses

Details locating and replacing primary and secondary fuses for fixture repair.

Changing the XLR pin-out

How to modify the XLR pin-out configuration using jumpers on the circuit board.

Changing lenses

Instructions for attaching and removing optional lens hoods for beam angle adjustment.

Cleaning the optical path

Procedures for cleaning optical components like lenses and filters using specific cleaning agents.

Cleaning the fans

Explains the importance of fan cleaning for cooling and how to perform it.

Replacing the lamp

Steps for replacing the lamp and resetting lamp hour/strike counters.

Optimizing lamp alignment

Guide on adjusting lamp position for even light distribution using adjustment screws.

Changing voltage and frequency settings

How to adjust internal settings for different AC power supply voltages and frequencies.

UPDATING SOFTWARE

Normal upload

Standard procedure for updating fixture software remotely using an upload device.

Boot mode upload

Guide to performing software updates when the fixture is in boot mode or if data is corrupted.

APPENDIX A: DMX PROTOCOL

DMX channel

Detailed breakdown of DMX channels, values, percentages, and their corresponding functions.

APPENDIX B: ERROR MESSAGES

Display readout

Lists error messages, their causes, and recommended actions for troubleshooting.

APPENDIX C: TROUBLESHOOTING

Problem

Common issues, probable causes, and remedies for fixture malfunctions.

APPENDIX D: PCB LAYOUT

PCB LAYOUT

Diagram of the main circuit board with labels for components and connectors.

APPENDIX E: SPECIFICATIONS

Measurements

Physical dimensions and weight specifications for the MAC 600/E fixture.

Electrical, magnetic ballast version

Electrical data including ballast taps, power, current, and power factor for magnetic ballast models.

Electrical, electronic ballast version

Electrical data for electronic ballast models, including transformer taps, power, current, and power factor.

Fuses

Lists the specific fuses used in the MAC 600/E, their types, and ratings.

Communication

Details communication protocols, DMX start code, and recommended cable types.

Compatible lamps

Lists compatible lamps with their power, efficiency, life, color temp, and part numbers.

Photometric

Provides photometric data such as total luminous flux and center intensity values.

Thermal

Specifies maximum ambient and surface operating temperatures for the fixture.

Accessories

Lists available accessories for the MAC 600/E, including flight cases and lens hoods.

Martin MAC 600 Specifications

General IconGeneral
BrandMartin
ModelMAC 600
CategoryLighting Equipment
LanguageEnglish

Related product manuals