Maxxus CX 5.1 User Manual

21
ENG
Step 4: Setting the Training Time
The value in the “TIME” window ashes. Enter the training time by turning the control knob clockwise / anti-clockwise. You
can set the exercise time from 1:00 to 99:00 minutes in 1-minute increments.
Step 5: Training Start
Press the START / STOP key to start exercising.
Training End
After the training time has expired, the training is automatically ended.
Program Procedure
The cockpit determines the current heart rate of the user and compares it continually with the desired target heart rate.
If the current heart rate is lower or higher than the target heart rate, the cockpit automatically increases or decreases the
resistance level.
If the current heart rate is within +/- 5 beats / minute below or above the target heart rate, the cockpit will maintain the cur-
rent resistance level.
If the cockpit cannot determine the user’s heart rate, the display shows “?”. In this case, check the correct position and bat-
tery power of the chest belt and make sure that it is an uncoded belt with the 5 kHz transmission frequency.
Example:
Target heart rate is 120 - no change in the brake level at a current heart rate of 115 ~ 125 beats / minute.
Watt-controlled training programs (WATT)
In this type of training the power in watts selected by the user is kept constant permanently by the cockpit. The user’s output
(watts) results from the current resistance level and the current pedalling speed. To keep the power constant, the cockpit
reduces the resistance level as soon as the user increases the pedalling speed. If the user reduces the pedalling speed, the
cockpit automatically increases the resistance level. This is also called speed-independent training
The user has three xed watt-training proles and a watt-constant program to choose from.
Step 1: Selecting a Program
Turn on the exerciser. An “M” will ash in the upper part of the display. Select the program “W” by turning the control knob
clockwise / anticlockwise and conrm your selection by pressing it.
Step 2: Setting Watt Value
The value in the “WATT” window ashes. Enter the desired wattage by turning the dial clockwise / anti-clockwise. Inputs
from 10 to 350 watts in 5-watt increments are possible. Conrm your entry by pressing the control knob.
Step 3: Setting the Training Time
The value in the “TIME” window ashes. Enter the desired training time by turning the control knob clockwise / anti-clock-
wise and conrm your entry by pressing it.
Step 4: Training Start
Press the START / STOP key to start exercising.
Training End
After the training time has expired, training will end automatically.
Cockpit
21
Mains Adapter
Take the connection cable of the mains adapter (D08) included in the delivery. Plug the connection cable into the socket on
the front of the main frame (A01). Then, connect the mains adapter (D08) to a power socket.
CAUTION:
This device should only be connected to an earthed socket that has been installed by a qualified electrician. Do not use
a socket strip for the connection. If an extension cable is necessary, ensure that it complies with the VDE regulations and
guidelines.
Connecting the Device
CAUTION:
Before connecting the mains adapter to the device, always ensure that you are using the mains adapter supplied specifically
with the device. Using a different mains adapter may result in damage to the electronic components, for which
the manufacturer cannot be held liable.
When connecting the device to the power supply, always connect the power cable to the exerciser first before plugging it
into a power outlet. Likewise, when disconnecting the exerciser from the power supply, always disconnect the power cable
from the mains first.
Switching on the Device
First connect the power cable to the exerciser and then connect the mains cable to the power socket, the cockpit turns on
automatically. If the training device is already connected to the mains, but the cockpit is in stand-by
mode, activate the cockpit by pressing any key or by moving the pedals.
Turning off the Device
When inactive for more than 4 minutes, the cockpit automatically switches to stand-by mode. Once you have finished your
workout you should always disconnect the exerciser from the mains. Always unplug the mains cable from the wall socket
first and then remove the power cable.
Mains Connection
16
Cockpit

Maxxus CX 5.1 Specifications

General

Brand	Maxxus
Model	CX 5.1
Category	Fitness Equipment
Language	English