Need help?Do you have a question about the McIntosh C1100 and is the answer not in the manual?
General| Type | Preamplifier |
|---|---|
| Total Harmonic Distortion | 0.005% |
| Frequency Response | 20Hz to 20kHz +0, -0.5dB |
| Input Impedance | 44K ohms |
| Output Impedance | 200 ohms |
| Dimensions | Each chassis: 17-1/2" (44.45cm) width x 6" (15.24cm) height (including feet) x 18" (45.72cm) depth (including front panel and cables) |
| Rated Output Voltage | 2.5V RMS |
| Phono Inputs | 2 (MM/MC) |
| Balanced Outputs | 2 |
| Unbalanced Outputs | 2 |
| Maximum Voltage Gain | 15dB |
| Gain | 60dB (MC Phono); 40dB (MM Phono) |
| Inputs | High Level, Phono |
| Outputs | Balanced, Unbalanced |
Essential safety guidelines to read before operating the equipment.
How to get help for McIntosh products from dealers or the company.
Information for returning the product for repair to the dealer or McIntosh Service.
Details about the C1100 system, components, and operating principles.
Descriptions and pin configurations for various connectors used in the C1100 system.
Overview of the C1100 Tube Preamplifier and its sonic characteristics.
Detailed list of technological advancements and capabilities of the C1100.
Diagrams illustrating the physical dimensions of the C1100C controller.
Recommendations for custom cabinet installation, including ventilation and spacing.
Diagrams illustrating the physical dimensions of the C1100T tube preamplifier.
Recommendations for custom cabinet installation, including ventilation and spacing.
Illustration and identification of rear panel connectors for the C1100C controller.
Illustration and identification of rear panel connectors for the C1100T preamplifier.
How to connect power control cables between components for system power management.
How to connect data and audio cables for source components.
How to connect for home theater passthru functionality.
How to connect the controller to the preamplifier unit.
Explains the function of each button on the HR085 remote control.
Guidance on using the remote control for Trim and Output Selection functions.
Detailed explanation of the C1100 Controller's front panel buttons and display.
Description of the C1100T preamplifier's front panel meters and headphone jack.
Instructions for navigating and using the C1100's setup menu.
Table of default settings and how to check firmware version.
How to enable/disable inputs and rename them for customization.
Step-by-step guide to renaming input sources for easier identification.
How to configure outputs to be switched or always on.
How to manage headphone muting and related settings.
How to assign power control triggers to outputs or inputs.
How to assign specific data ports to source components.
How to set up the Passthru mode for home theater integration.
How to configure the baud rate for RS232 remote control.
How to switch between normal and alternate remote control codes.
How to disable the front panel IR sensor.
How to enable or disable the automatic power-off feature.
Steps to reset all adjustable settings to their factory defaults.
Instructions for powering the unit and selecting audio sources.
How to adjust volume and access various trim functions.
How to adjust balance and input trim levels for optimal sound.
How to control outputs and meter illumination.
How to adjust the brightness of the front panel information display.
How to set loading values for MC and MM phono inputs.
How to use headphone HXD, adjust gain, and mute audio.
Explanation of output meters and passthru mode.
How to use the headphones jack and make recordings.
Steps to reset the unit's microprocessors in case of malfunction.
Images showing the front and rear panels of the C1100 controller.
Images showing the front and rear panels of the C1100T preamplifier.
View of the internal components, including tubes, of the C1100T.
Detailed electrical performance data including frequency response and distortion.
Details on dimensions, weight, power requirements, and tube complement.
Guidelines for safely repacking the C1100 for shipment.
To Next Page
