EasyManua.ls Logo

MEDIATEK Genio 350 - User Manual

Default Icon
24 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
MediaTek Proprietary and Confidential. © 2022 MediaTek Inc. All rights reserved.
Unauthorized reproduction or disclosure of this document, in whole or in part, is strictly prohibited.
Version: 1.0
Release date: 2022-02-11
Use of this document and any information contained therein is subject to the terms and conditions set forth in
Exhibit 1. This document is subject to change without notice.
Genio 350
Evaluation Kit
Hardware User Guide

Other manuals for MEDIATEK Genio 350

Question and Answer IconNeed help?

Do you have a question about the MEDIATEK Genio 350 and is the answer not in the manual?

Summary

Overview

General Information

Provides general details about the Genio 350-EVK, highlighting its features and capabilities as an IoT platform.

Architecture and Block Diagram

Illustrates the system's architecture and component interconnections with a detailed block diagram.

Feature Summary

Lists the key hardware features and specifications of the Genio 350-EVK, including processor, memory, and peripherals.

Introduction

CPU (MT8365)

Details the MediaTek Genio 350 processor, its architecture, clock speed, and core features.

Power Management IC (MT6357)

Describes the MT6357 Power Management IC, including its converters, LDOs, and system management capabilities.

DRAM (Micron MT53 E768 M32 D4 DT-053)

Specifies the 3GB LPDDR4 DRAM, its memory clock, and dual-channel bus width.

eMMC Storage (SanDisk;Western Digital SDINBDA4_64 G)

Details the 64GB eMMC 5.0 storage, its interface, and usage for code and data.

M.2 Wi-Fi;Bluetooth Module (AzureWave AW-CB451 NF)

Describes the M.2 2230 WiFi/Bluetooth module, its chip, and supported wireless standards.

Optional On-Board WiFi Chip (MT6631)

Details the optional on-board MediaTek MT6631 chip for WiFi, Bluetooth, GPS, and FM support.

Interface and Connectors

Genio 350-EVK I;O Connectors

Lists and describes the various I/O connectors on the Genio 350-EVK board, including their designations.

System Power Paths

Explains the two power supply paths for the system, detailing connections via DC Jack and battery charger.

LED Indicators

Describes the status LEDs on the board, their locations, colors, and meanings.

UART

Details the two UART ports, their connectors, and usage for debugging and logging.

I2 C

Explains the four I2C buses, their modes of operation, and address support.

SPI

Describes the SPI interface, including its master/slave mode support and chip select.

PWM

Details the Pulse Width Modulation capabilities, including supported modes and frequency range.

Raspberry Pi like I;O Interface

Describes the 40-pin header providing Raspberry Pi compatible I/O, with pin assignments.

MicroSD Slot

Details the MicroSD card slot, its interface, and supported speed modes and bus widths.

Power and Function Key Interface

Explains the power and function key interface, including power-on, reset, volume buttons.

USB Device

Describes the USB Device port, typically used for ADB debug purposes.

USB Host

Details the USB Host port, used for connecting external USB devices.

Audio Interface (Earphone and Line Out)

Explains the 3.5mm earphone jack with microphone input and line out audio jack.

Microphones

Details the onboard analog and digital microphones, their types, and connections.

MIPI DSI Interface

Describes the 4-lane MIPI DSI interface for connecting displays and its data rate.

MIPI CSI Interface

Explains the two 4-lane MIPI CSI interfaces for camera modules and their data rates.

Ethernet MII and RMII Interfaces

Details the Ethernet MII/RMII interfaces, their configuration, and the RJ-45 connector.

How to Switch between HDMI and Ethernet Interfaces

Provides instructions on switching between HDMI and Ethernet interfaces due to shared GPIO pins.

HDMI Port

Describes the HDMI port, its connection via DPI, and resolution limitations.

Pin Mux for Other Interfaces

Explains GPIO sharing among various interfaces like HDMI, M.2, WiFi, and JTAG.

On-Board Antenna

Describes the three on-board antennas for WiFi, Bluetooth, and GPS modules.

LCM FPC Installation

Provides instructions on how to connect the LCM FPC (Flexible Printed Circuit) cable.

How to Power Up The System

Step-by-step instructions on how to power on the Genio 350-EVK board.

How to flash Image to the Board

Guides on downloading prebuilt images and reflashing the board's software.

Debug

Explains how to set up debugging using Micro USB for UART logs and the required software.

Camera Sub-Board

Feature

Lists the features of the camera sub-board, including MIPI CSI interfaces and camera module support.

Camera Sub-Board Block Diagram

Presents a block diagram illustrating the components and connections of the camera sub-board.

How to Configure the MIPI CSI Path

Provides jumper settings for configuring the MIPI CSI path for camera module connections.

Reference Documents

Contains in The Box

Lists the items included in the Genio 350-EVK evaluation kit package.

PCBA Version

Details the naming rule for PCBA versions of the main board and camera board.

Disclaimer

Contains legal disclaimers, warranty information, and intellectual property rights.

Power Distribution

Illustrates the power distribution across various components of the Genio 350-EVK system.

MEDIATEK Genio 350 Specifications

General IconGeneral
ProcessorMediaTek Genio 350
CPU Cores4
GPUArm Mali-G52
Process Technology12nm
Max RAM Support4GB
Storage InterfaceeMMC 5.1
Max Display Resolution1920 x 1080
AI AcceleratorNo
ConnectivityWi-Fi 5, Bluetooth 5.0
USBUSB 2.0
Memory TypeLPDDR4
Video EncodeH.264
Video DecodeH.264, H.265

Related product manuals