What to do if my Megmeet Media Converter shows 'The Current Hall is not Inserted'?
If your Megmeet Media Converter displays 'The Current Hall is not Inserted', check the current hall connector to ensure it is properly connected.
What to do if my Megmeet Dex CM3000 encoder fails (DexPM3000)?
If you're experiencing an encoder failure with your DexPM3000 Megmeet Media Converter, check whether the signal terminal of the code disc is firmly connected.
General| Category | Media Converter |
|---|---|
| Model | Dex CM3000 |
| Manufacturer | Megmeet |
| Input Frequency | 50/60Hz |
| Rated Power | 3000W |
| Cooling Method | Forced Air Cooling |
| Storage Temperature | -40°C to +85°C |
| Certifications | CE |
| Protection Features | OVP, OCP, OTP, SCP |
General introduction to the Dex CM3000 and PM3000 welding power sources.
Outlines the manual's purpose, content, and scope for users.
Explains safety warning symbols and their meanings for hazard identification.
Critical safety measures for installing the welding power source.
Covers safe handling procedures and general operational safety.
Additional general safety advice for users to follow during operation.
Safety advice related to environment, ventilation, and PPE.
Key points to observe for safe and efficient operation.
Guidelines and potential risks associated with machine scrapping.
Brief overview of the Dex CM3000 and PM3000 welding machine models.
Describes the main components of the welding system with a diagram.
Procedures for unpacking and environmental/space requirements for installation.
Precautions for handling the welder and electrical connection safety.
Instructions for connecting the 380VAC power input and welding torch.
Steps for connecting the ground cable and installing the wire feeder roller.
Instructions for installing the wire spool and connecting the gas supply system.
Description of the controls and indicators on the CM3000 front panel.
Instructions on how to operate the buttons and knobs for function selection.
Operation of wire inching and gas detection functions.
Explanation and selection of synergic and separate welding modes.
How to adjust arc hardness for optimal welding performance.
Overview of the CM3000's internal menu and parameter settings.
Setting parameters for wire feed speed and gas timing functions.
Configuration of soft-start and transition times for wire feeding.
Setting post-gas time and wire inching speed parameters.
Adjusting the DC burn-back voltage parameter for welding control.
Configuration of DC burn-back time and chopping time parameters.
Adjusting parameters for short-circuit current slope and amplitude.
Setting welding control modes and wire feed speed percentage.
Adjusting synergic voltage and arc dynamics for arc starting.
Setting arc starting time and DC welding energy control.
Configuration of MMA arc-striking and hot-start current.
Setting MMA thrusting current and arc ending wire feed speed.
Adjusting synergic voltage and arc dynamics for arc ending.
Setting arc ending time and spot welding time parameters.
Procedures for querying software version and error records.
Querying machine model and switching MMA function on/off.
Procedure for restoring the welder to its factory default settings.
Description of the PM3000 front panel controls and key functions.
Detailed explanation of each key's function on the PM3000.
Operation of wire inching, gas detection, and synergic/separation modes.
Adjusting arc dynamics and setting arc starting parameters.
Setting parameters for the arc ending phase of welding.
Instructions and logic diagram for spot welding mode.
Instructions and logic diagram for the 2 T welding mode.
Instructions and logic diagrams for 4 T and Special 4 T welding modes.
Procedures for storing and recalling welding parameters.
How to access and navigate the internal menu system.
Overview of internal menu functions and F10 parameter setting.
Setting parameters for pre-gas, transition, and post-gas timing.
Configuration of soft-start time and wire inching speed.
Setting parameters for DC burn-back voltage and time.
Setting the DC chopping time parameter for welding control.
Adjusting parameters for short-circuit current slope and amplitude.
Setting the DC welding energy control parameter.
Setting parameters for pulse current amplitude and time.
Setting parameters for pulse burn-back and chopping time.
Configuration of double pulse frequency and duty cycle.
Setting double pulse current intensity and weak pulse voltage correction.
Setting the correction value for intense pulse voltage.
Configuration of MMA arc-striking, hot-start, and thrusting current.
Procedures for querying software version and error records.
Querying machine model and switching MMA function.
Procedure for restoring the welder to its factory default settings.
How to identify faults using the red indicator light on the welder panel.
Common fault codes displayed and their corresponding solutions.
Additional fault codes and their descriptions and solutions.
Steps and key points for performing daily inspections.
Specific inspection items for the welding machine and its cables.
Schedule and detailed procedures for periodic maintenance checks.
Details on warranty coverage, maintenance, and customer service.
Detailed technical data for the Dex CM3000 and Dex PM3000 welding power sources.
Schematic illustrating the electrical connections within the welder unit.
Configuration and ordering information for the Dex CM3000 welder.
Details on process configuration options for the Dex CM3000.
Configuration and ordering information for the Dex PM3000 welder.
Details on process configuration options for the Dex PM3000.
Detailed illustration of welder components with corresponding part numbers.
Information on the warranty scope, period, and service claim policies.
To Next Page
