Why won't my Menuett dishwasher start?
Your Menuett dishwasher might not start due to several reasons: a tripped fuse (replace the fuse or reset it, and remove other appliances sharing the circuit), the power not being on (ensure the dishwasher is switched on, the door is properly closed, and the plug is correctly inserted), or the door panel not being properly closed (close the panel so that the lock grips).
What to do if Menuett 802-469 not cleaning dishes properly?
If your Menuett dishwasher isn't cleaning dishes well, consider these possibilities: the dishes may not be correctly placed (refer to the section on filling the dishwasher baskets), the wash programme choice is incorrect (select a more powerful wash programme, consulting the wash programmes table), there's too little detergent (use more or a different kind), an object is blocking water from the rinse arms (rearrange the dishes), or the filter is blocked or incorrectly fitted, potentially blocking the rinsing arm nozzles (clean and/or properly fit the filter unit and clean the nozzles on the rinse arms).
How to fix Menuett dishwasher not drying dishes?
If your Menuett dishwasher isn't drying dishes, it could be due to improper loading (follow the loading instructions), insufficient rinsing agent (increase the amount or fill the container), removing dishes too early (wait until they are lukewarm and let steam escape), selecting an incorrect programme (use a longer wash programme), or low-quality cutlery (some aren't dishwasher-safe).
What to do if Menuett 802-469 has foam inside?
If there's foam in your Menuett dishwasher, it's likely due to using the wrong type of detergent (use only dishwasher detergent). If foam forms, open the door and let it evaporate. Pour about 4.5 liters of cold water into the dishwasher, close the door, and start the rinse programme to empty the water. Repeat if needed. Also, always wipe up any spilt rinsing agent immediately.
Why is my Menuett 802-469 Dishwasher leaving a milky coating on glasses?
A milky coating on glasses from your Menuett dishwasher is likely due to soft water combined with too much detergent. Use less detergent if your water is soft and wash the glasses with a short wash programme.
What to do if Menuett dishwasher water won't pump out?
If the water isn't pumping out of your Menuett dishwasher, check the outlet hose for clinches. Also check the coarse filter for clogs. Finally, see if the kitchen sink is blocked, and if so, contact a plumber.
Why are there rust stains on cutlery in my Menuett dishwasher?
Rust stains on cutlery in your Menuett dishwasher can occur if the cutlery isn't stainless steel. It can also happen if a wash programme wasn't run immediately after filling salt, or if too much salt was dosed. Always run a quick programme with an empty machine after filling salt. Also, ensure the cap on the salt container is properly sealed and screwed on tightly.
Why does my Menuett 802-469 have white film inside?
If there's a white film inside your Menuett dishwasher, it's likely due to hard water. Clean the inside with a damp sponge and dishwasher detergent, wearing rubber gloves. Only use dishwasher detergents to avoid foaming.
Why is my Menuett 802-469 Dishwasher making a knocking noise?
A knocking noise in your Menuett dishwasher often means the rinse arms are hitting objects in the cutlery basket. Cancel the wash programme and rearrange any utensils blocking the rinsing arms.
Why does my Menuett 802-469 Dishwasher have black or grey stains on the dishes?
Black or grey stains on dishes in your Menuett dishwasher usually indicate that an aluminum object has scraped against the dishes. Remove the stains with a mild abrasive detergent.
Ensures the dishwasher is properly earthed to prevent electric shock risks.
Guidelines on proper operation, safety precautions, and intended use of the appliance.
Provides the physical dimensions required for installing the dishwasher.
Steps for preparing the installation site and positioning the appliance correctly.
Details on connecting the dishwasher to the power supply, including safety and data.
Instructions for connecting the water inlet hose to a cold water supply.
Guidance on connecting the drain hose to the waste water system.
Instructions on how to start a wash programme and how to change it mid-cycle.
Details on the filter system components and their functions.
Common causes and solutions when the dishwasher fails to start.
Troubleshooting for problems related to water not being pumped out of the dishwasher.
General| Energy Efficiency Class | A |
|---|---|
| Number of Place Settings | 12 |
| Drying Class | A |
| Width | 60 cm |
| Height | 85 cm |
| Depth | 60 cm |
To Next Page
