36
Specifications
CONSOLE P/N 10365)
12 volt positive or negative ground with built-in switching
regulator. High intensity vacuum florescent display. Current
draw is less than 1 amp without solenoids.
CONNECTOR SYSTEM
Packard Electric “Weather Pack” sealed automotive type
connectors.
FM750 GFN FLOWMETER P/N 11501
Flow capability is 2-40 GPM (7.5 - 151 lpm) with a 4 PSI (.27
bar) pressure drop at 40 GPM (151 lpm). Pressure range to
150 PSI (10.3 bar). Maximum liquid temperature 130° F (54.4°
C). Materials are glass-filled nylon housing, nylon turbine
with stainless steel shaft and bearings.
FM750 SS FLOWMETER P/N 10131
Flow capability is 2-40 GPM (7.5 - 151 lpm) with a 4 PSI (.27
bar) pressure drop at 40 GPM (151 lpm). Pressure range to
150 PSI (10.3 bar). Maximum liquid temperature 130° F (54.4°
C). Materials are 304 and 316 stainless steel, teflon, nylon,
tungsten carbide and carbon graphite. (Other materials
available).
FM500 FLOWMETER P/N 11594
Flow capability is .5 - 5 GPM (1.9 - 19 lpm) with a 1 PSI (.07
bar) pressure drop at 5 GPM (19 lpm). Pressure range to 500
PSI (34.5 bar). Maximum liquid temperature 130° F (54.4° C).
Materials are glass-filled polypropylene housing and nylon
turbine, special alloy shaft and jeweled bearing system.
FM2000 FLOWMETER P/N 11259
Flow capability is 19 - 198 GPM (72 -750 lpm). Pressure
range to 285 PSI (19.6 bar). Materials are rilsan housing with
stainless steel turbine and bearings.
MT 1” SERVO VALVE P/N 11218
6-8 RPM @ 6 volts DC. Maximum recommended operating
pressure 150 PSI (10.3 bar). Glass filled nylon body, stainless
steel butterfly and viton seal.
• Flow Rates @ 20 PSI (1.4 bar) drop:
Open = 67 GPM (254 lpm) Half = 29 GPM (110 lpm)
Closed = 3.5 GPM (13.2 lpm)
• Flow Rates @ 40 PSI (2.7 bar) drop:
Open = 95 GPM (360 lpm) Half = 42 GPM (159 lpm)
Closed = 5 GPM (19 lpm)
MT ¾” SERVO VALVE P/N 11522
6-8 RPM @ 6 volts DC. Maximum recommended operating
pressure 150 PSI (10.3 bar). Glass filled nylon body, stainless
steel butterfly and viton seal.
• Flow Rates @ 20 PSI (1.4 bar) drop:
Open = 37 GPM (140 lpm) Half = 16 GPM (60 lpm)
Closed = 1.4 GPM (5.2 lpm)
• Flow Rates @ 40 PSI (2.7 bar) drop:
Open = 51 GPM (193 lpm) Half = 23 GPM (87 lpm)
Closed = 2 GPM (7.5 lpm)
SPARE PARTS AND ACCESSORIES
The following parts are available from you local Micro-Trak
dealer or directly from the factory. Prices and specifications
are good for the U.S.A. only and subject to change without
notice.
When ordering parts, specify product model, description of
parts you want to order and their respective part number. All
parts carry 90 day warranty.
PART NUMBER DESCRIPTION
12069 Magnet (6 each)
10013 Speed Sensor Mount Bracket
10045 14” (35 cm) Black Cable Ties
10075 Hardware Bag
10080 Magnet Clip
11501 FM750 GFN Flowmeter (no cable)
10131 FM750 SS Flowmeter (no cable)
10365 Console Only - MT-3000
10423 Console Mount Knob (1)
12245 MT-3000 Reference Manual
11218 1” MT Electric Servo Valve 0-150 PSI
11522 ¾” MT Electric Servo Valve 0-150 PSI
10416 3’ (1 m) Speed Sensor Cable
10417 3’ (1 m) Flow Sensor Cable
11311 5’ 1.5 m) Servo Valve Cable
10419 3’ 91 m) Solenoid Cable
10445 Female Dust Cover
10447 Male Dust Cover
10449 10’ (3 m) Extension Cable
10450 5’ (1.5 m) Extension Cable
10474 Compression Fitting Kit
10477 Terminal Fitting Kit
10485 Pressure Tubing Extension Kit
10487 MT-3000 Run/Hold Kit
10422 Console Mounting Bracket
00216 Electric Solenoid Valve (1)
10415 Main Wiring Harness
11503 O-Ring. FM750 GFN Flowmeter
10137 Gasket, FM 750 SS Flowmeter
00118 Boost Solenoid Kit
00119 Convenience Kit
00125 Trak-Star Ultrasonic Speed Sensor
00132 FM500 Flowmeter (w/3’ cable)
11259 FM2000 Flowmeter (no cable)
11335 1” MT HP Servo Valve 0-300 PSI (0-21 bar)
11547 ¾” MT HP Servo Valve 0-300PSI (0-21 bar)
00141 NH3500 Kit
10876 15’ (4.5 m) Extension Kit
10829 20’ (6 m) Extension Kit
To Next Page
Loading...
