Microlife BP B2 Basic User Manual

5Microlife BP B2 Basic
EN
6. Using a mains adapter
You can operate this device using the Microlife mains adapter (DC
6V, 600 mA).
1. Plug the adapter cable into the mains adapter socket 6 in the
blood pressure monitor.
2. Plug the adapter plug into the wall socket.
When the mains adapter is connected, no battery current is
consumed.
7. Error messages
If an error occurs during the measurement, the measurement is
interrupted and an error message, e.g. «ERR 3», is displayed.
* Please immediately consult your doctor, if this or any other
problem occurs repeatedly.
8. Safety, care, accuracy test and disposal
 Follow instructions for use. This document provides important
product operation and safety information regarding this device.
Please read this document thoroughly before using the device
and keep for future reference.
 This device may only be used for the purposes described in
these instructions. The manufacturer cannot be held liable for
damage caused by incorrect application.
 This device comprises sensitive components and must be
treated with caution. Observe the storage and operating condi-
tions described in the «Technical specifications» section.
 The cuffs are sensitive and must be handled with care.
 Only pump up the cuff once fitted.
 Do not use this device if you think it is damaged or notice
anything unusual.
 Never open this device.
 Read the additional safety information provided within the indi-
vidual sections of this instruction manual.
 The measurement results given by this device is not a diag-
nosis. It is not replacing the need for the consultation of a physi-
cian, especially if not matching the patient’s symptoms. Do not
rely on the measurement result only, always consider other
potentially occurring symptoms and the patient’s feedback.
Calling a doctor or an ambulance is advised if needed.

Only use the Microlife mains adapter available as an orig-
inal accessory appropriate for your supply voltage.

Ensure that neither the mains adapter nor the cable are
damaged.
Error Description Potential cause and remedy
«ERR 1»
AS
Signal too
weak
The pulse signals on the cuff are too
weak. Re-position the cuff and repeat
the measurement.*
«ERR 2»
AR-B
Error signal During the measurement, error signals
were detected by the cuff, caused for
instance by movement or muscle
tension. Repeat the measurement,
keeping your arm still.
«ERR 3»
AR-C
Abnormal
cuff pressure
An adequate pressure cannot be
generated in the cuff. A leak may have
occurred. Check that the cuff is
correctly connected and is not too
loose. Replace the batteries if neces-
sary. Repeat the measurement.
«ERR 5» Abnormal
result
The measuring signals are inaccurate
and no result can therefore be
displayed. Read through the checklist
for performing reliable measurements
and then repeat the measurement.*
«HI» Pulse or cuff
pressure too
high
The pressure in the cuff is too high
(over 299 mmHg) OR the pulse is too
high (over 200 beats per minute).
Relax for 5 minutes and repeat the
measurement.*
«LO» Pulse too low The pulse is too low (less than 40 beats
per minute). Repeat the measure-
ment.*
Safety and protection
Error Description Potential cause and remedy

Microlife BP B2 Basic Specifications

General

Type	Automatic
Cuff size	22 - 42 cm
Control type	Buttons
Product color	White
Number of users	1 user(s)
Measuring method	Oscillometric
Memory registers	30
Pulse rate range	40 - 200
Speaking function	No
Placement supported	Upper arm
Units of measurement	mmHg
Mean arterial pressure	Yes
Display type	LCD
Battery type	AA
Battery voltage	1.5 V
Battery technology	Alkaline
Battery life (CIPA standard)	920 shots
Number of batteries supported	4
Quantity per pack	1 pc(s)
Pressure accuracy	1 mmHg
Pressure measurement range	20 - 280 mmHg

Weight and Dimensions

Depth	90 mm
Width	131 mm
Height	60.5 mm
Weight	277 g