Microtest CT-8750 - Pin Search Function

To Next Page

To Previous Page

CHAPTER II System Function and Configuration

P 21

II.1.C.e

Insulation Calibration



Operation Procedure

(a) Operation is the same before, in the subordinate menu of calibration, using

[↑] or [↓] to select (5) Insu.Cal. LCD display as following

(b) Press [Enter], LCD display as following

closer to the standard voltage as much as possiable

(d) After setup finished, press S5 [DONE] to save

(e) If you want to abandon data, press S6[QUIT] to exit from this screen

Main Page

CT-8750 User's Guide2
Table of Contents3
Chapter I General Exposition6
Package & Equipment6
Symbol & Word6
General Operation Guidelines7
I.4 Tester Tour8
Tester Tour8
I.4.Athe Front Panel8
I.4.Bthe Points9
I.4.Cthe Rear Panel11
I.5 System Installation12
System Installation12
Key Definition12
I.6.Asyskey Group12
I.6.Bfastkey Group12
I.6.Ceditkey Group13
I.6.D [Enter] Confirmation13
I.6.E [Test] to Start Test13
I.6.F [Reset] System will be Re-Started When Pressed to Perform the13
Warm Start13
I.6.Gsoftkey Group13
Chapter II System Function and Configuration14
II.1 System Function14
II.1.Aselftest15
II.1.Bsystem Version Information16
II.1.Ccalibration17
II.1.C.a Open/Short Calibration18
II.1.C.b Conductance Calibration19
II.1.C.C DC H//V Calibration20
II.1.C.D Ac H/V Calibration21
II.1.C.e Insulation Calibration22
II.1.Dpin Search23
II.2 System Setup24
II.2.Asystem Environments Setup24
II.2.A.a Power on Self-Test25
II.2.A.b Power Line Frequency25
II.2.A.C Key Stroke Sound25
II.2.A.D Key Operation26
II.2.A.e Lcd Contrast27
II.2.A.f Lcd Inverse27
II.2.A.g Language27
II.2.Btest Environment Setup28
II.2.B.a Test Alarm28
II.2.B.b Display Test Data29
II.2.B.C Printer Data Report29
II.2.Cdate & Time Setup29
II.2.Dpassword Setup30
II.3 Print Function31
II.4.B O/S Scanning Speed32
II.4 Open/Short Setup & Test32
II.4.A O/S Threshold Setup32
II.4.C O/S End Detection33
II.4.Dint. S/O Stop Mode33
II.4.Eint. O/S Timer33
II.5 Statistic Report33
Chapter III Sequence Test Setup35
III.1 Test Condition Setup35
III.1.Aopen/ Short35
III.1.Bconductance Setup36
III.1.C R/L/C Setup37
III.1.Dtest Mode Edit41
III.2 Run the Sequence Test42
III.2.Arun the Real Time Sequence Test42
III.2.Brun the Existed Sequence Test43
III.3 File Management44
III.3.Aopen File44
III.3.Bopen New File45
III.3.Cdelete File45
III.3.Dsort File46
III.4 View Mode47
Appendix A、 Ct-8750 Cable Sets48
Appendix B、 Ct-8750 Test Range and Function50
Appendix C、 Ct-8750 Specification51

Microtest CT-8750 - Pin Search Function

Table of Contents

Related product manuals