How to clear clogged nozzles on my MIMAKI UCJV300-160 Printer?
To clear clogged nozzles, you can try the following: * Perform head cleaning. * Perform print head nozzle washing. * Perform [MENU] > [Maintenance] > [INK FILL].
What to do if the ink has leaked from my MIMAKI UCJV300-160 Printer?
If an ink leak occurs, immediately turn off the main power and unplug the power cable. Then, contact your local dealer or our service office.
What to do if the light-blocking cover comes off my MIMAKI UCJV300-160 Printer?
If the light-blocking cover comes loose, reattach it by following these steps: 1. Insert the lug on one side of the light-blocking cover into the corresponding hole in the tank. 2. Insert the lug on the other side while pushing in toward the first hole.
Why does the media jam or get dirty in my MIMAKI UCJV300-160?
To address media jams or dirty media, consider the following: * Ensure you are using the recommended media. * Avoid using curled media or media with folded ends. * Use the take-up unit to adjust or reload the media.
How to fix image defects occurring on my MIMAKI UCJV300-160 Printer?
To address image defects, try the following: * Remove any paper scraps or debris from areas the head passes over, such as media holders. * Perform head cleaning. * Perform feed correction. * Clean the wiper. * Clean the cap rubber. * Clean the carriage underside.
How to correct misaligned print and cut positions on my MIMAKI UCJV300-160?
If the print and cut positions are misaligned, use the MIMAKI RIP software (RasterLink) to print a correction pattern. Then, check the pattern and manually input correction values.
Why does the cut position shift on my MIMAKI UCJV300-160?
If the cut position shifts, it may indicate a problem with the register mark sensor. Perform the operation used to check the responsiveness of the register mark sensor. Note that you cannot check the responsiveness manually.
How to troubleshoot a MIMAKI UCJV300-160 when the power does not turn on?
To resolve the issue of the power not turning on, ensure the power plug is securely inserted into the power outlet, use the power cable provided, and turn on the main power.
What to do if the MIMAKI Printer power does not turn on?
If the MIMAKI Printer does not turn on, ensure the power plug is securely connected to the power outlet. Also, make sure you are using the power cable provided with the printer and that the main power is turned on.
How to fix image defects on MIMAKI UCJV300-160?
To fix image defects on your MIMAKI Printer, remove any paper scraps or debris from areas where the head passes, such as media holders. You may also need to perform head cleaning, feed correction, wiper cleaning, cap cleaning, and carriage underside cleaning. Additionally, consider performing an ink fill, replacing the wiper, or registering nozzle recovery.
Covers liability limitations, fire risks, and general safety warnings.
Addresses potential electromagnetic interference and mitigation steps.
Details compliance with Federal Communications Commission regulations.
Explains the meaning of warning, caution, and notice symbols used in the manual.
Provides essential safety guidelines for operating the machine and handling liquids.
Outlines critical requirements for safe and proper installation environments.
Describes safety interlock features and locations of warning labels on the machine.
Details safety measures for handling ink, cleaning solutions, and waste ink.
Provides information on ink types, capacity, expiration, and storage conditions.
Specifies the necessary clearance around the machine for operation and maintenance.
Provides instructions and precautions for moving the machine.
Identifies and describes the main parts and components of the printer.
Details the procedure for connecting the power cable and turning the machine on/off.
Explains how to connect the printer to a PC using USB or LAN interfaces.
Guides through the initial setup of the printer system, including RIP software.
Provides instructions for replacing ink bottles and managing ink levels.
Outlines the step-by-step process for performing a print job.
Explains how to adjust the gap between the print head and the platen for optimal printing.
Details how to position pinch rollers for different media widths.
Provides instructions for loading both roll and leaf media onto the printer.
Guides on configuring pinch roller settings for various media and tools.
Explains how to perform test prints to check ink quality and identify defects.
Describes different head cleaning procedures for resolving print defects.
Explains how to adjust media feed amounts to correct printing defects.
Details how to adjust the drop position for bi-directional printing to improve accuracy.
Guides on preparing and sending print data from RIP software.
Explains the procedure for cutting media after printing.
Outlines the steps involved in performing a cutting job.
Provides instructions for installing cutters and pens in the machine.
Explains how to configure speed, pressure, and offset for cutting.
Guides on performing test cuts to verify settings and quality.
Details how to set up and initiate cutting jobs.
Outlines the workflow for cutting based on printed register marks.
Explains how to create and use register marks for accurate cutting.
Details how to configure settings for detecting printed register marks.
Explains the procedure for identifying the origin point of register marks.
Describes the process for using ID Cut data for automated cutting.
Covers setting print conditions for specific media and temporary usage.
Details various maintenance actions and nozzle recovery functions.
Explains settings for auto power-off, media detection, and network configuration.
Covers nozzle clogging detection and automatic recovery settings.
Provides access to machine status, usage, and version information.
Details settings for register mark detection, cut modes, and offsets.
Essential guidelines for performing maintenance safely and effectively.
Lists routine cleaning and inspection tasks to be performed daily and weekly.
Lists necessary tools and consumable items for maintenance.
Step-by-step guide for cleaning the print head wiper.
Instructions for cleaning the printer's cap to maintain nozzle health.
Details how to clean the Nozzle Check Unit sensor.
Guides on cleaning the underside of the carriage and UV-LED lamp.
Explains how to clean or replace the mist filter.
Describes nozzle washing to resolve print defects when cleaning fails.
Provides instructions for cleaning the ink discharge channel.
Details how to clean the media sensors for accurate detection.
Explains how to clean the media holder for proper media feeding.
Guides on cleaning the platen area to ensure proper media handling.
Instructions for cleaning the external covers of the machine.
Provides guidelines for preparing the machine for long-term storage.
Covers replacement procedures for wipers, caps, filters, and rollers.
Details replacement for cutting-specific consumables like cutters and pen lines.
Provides solutions for common problems like power, printing, and media issues.
Lists error and warning messages with their causes and corrective actions.
Lists technical specifications for the printer models.
Details specifications related to the cutting functionality.
General| Maximum Print Width | 1, 610 mm |
|---|---|
| Resolution | 1200 x 1200 dpi |
| Ink Type | UV-curable ink |
| Cutting Function | Yes |
| Media Thickness | Up to 1 mm (0.04") |
| Media Width | 1, 620 mm (63.8") |
| Connectivity | USB2.0, Ethernet |
| Print Speed | Up to 25.8 m²/h |
| Print Technology | UV-LED Inkjet |
To Next Page