Mitsubishi FR-A740-00023-EC - Page 85

75
Parameter List
Parameter List
4
PARAMETERS
S-pattern acceleration/
deceleration D
516
S-pattern time at a start of acceleration 0.1 to 2.5s
0.1s 0.1s 170
517
S-pattern time at a completion of
acceleration
0.1 to 2.5s
0.1s 0.1s 170
518
S-pattern time at a start of deceleraiton 0.1 to 2.5s
0.1s 0.1s 170
519
S-pattern time at a completion of
deceleraiton
0.1 to 2.5s
0.1s 0.1s 170
⎯ 539
Modbus-RTU communication check
time interval
0 to 999.8s, 9999
0.1s 9999 333
USB
547
USB communication station number 0 to 31
1 0 347
548
USB communication check time
interval
0 to 999.8s, 9999
0.1s 9999 347
Communication
549
Protocol selection 0, 1
1 0 333
550
NET mode operation command source
selection
0, 1, 9999 1 9999 310
551
PU mode operation command source
selection
1, 2, 3 1 2 310
Current average
value monitor
555
Current average time 0.1 to 1.0s
0.1s 1s 378
556
Data output mask time 0.0 to 20.0s
0.1s 0s 378
557
Current average value monitor signal
output reference current
0 to 500/0 to 3600A *2 0.01/0.1A *2
Rated
inverter
current
378
⎯ 563
Energization time carrying-over times (0 to 65535)
1 0 244
⎯ 564
Operating time carrying-over times (0 to 65535)
1 0 244
Second motor
constants
569
Second motor speed control gain 0 to 200%, 9999
0.1% 9999 140
Multiple
rating
570
Multiple rating setting 0 to 3
1 2 149
⎯
571 Holding time at a start 0.0 to 10.0s, 9999 0.1s 9999 169
⎯ 573
4mA input check selection 1, 9999
1 9999 293
⎯ 574
Second motor online auto tuning 0, 1
1 0 191
PID control
575 Output interruption detection time 0 to 3600s, 9999 0.1s 1s 348
576
Output interruption detection level 0 to 400Hz
0.01Hz 0Hz 348
577
Output interruption cancel level 900 to 1100%
0.1% 1000% 348
Travers function
592
Traverse function selection 0, 1, 2
1 0 369
593 Maximum amplitude amount 0 to 25% 0.1% 10% 369
594
Amplitude compensation amount
during deceleration
0 to 50%
0.1% 10% 369
595
Amplitude compensation amount
during deceleration
0 to 50% 0.1% 10% 369
596 Amplitude acceleration time 0.1 to 3600s 0.1s 5s 369
597
Amplitude deceleration time 0.1 to 3600s
0.1s 5s 369
⎯
611
Acceleration time at a restart 0 to 3600s, 9999
0.1s 5/15s *2 254
⎯
665
Regeneration avoidance frequency
gain
0 to 200% 0.1% 100% 371
⎯
684
Tuning data unit switchover 0, 1
1 0 181
⎯
800 Control method selection 0 to 5, 9 to 12, 20 1 20
87,
140
⎯
802 *5
Pre-excitation selection 0, 1
1 0 194
Func-
tion
Parameter Name Setting Range
Minimum
Setting
Increments
Initial Value
Refer
to
Page
Customer
Setting