Mitsubishi FR-D720-5.5K - Page 141

132
Deleted functions
Pr. 98 Automatic torque boost selection
Pr. 99 Motor primary resistance
Replacement function (General-purpose magnetic flux
vector control)
(Pr. 80 Motor capacity)
(Pr. 90 Motor constant (R1))
Long wiring mode (setting value 10, 11 of Pr. 70)
Setting unnecessary (setting value 10, 11 of Pr. 240 is
deleted)
Changed parameter
number and name
Parameter
Number
Name
Parameter
Number
Name
Pr. 17 RUN key rotation direction selection Pr. 40 RUN key rotation direction selection
Pr. 21 Stall prevention function selection Pr. 156 Stall prevention operation selection
Pr. 28
Stall prevention operation reduction
starting frequency
Pr. 66
Stall prevention operation reduction
starting frequency
Pr. 30 Extended function display selection Pr. 160 Extended function display selection
Pr. 38 Frequency setting voltage gain frequency Pr. 125
Terminal 2 frequency setting gain
frequency
Pr. 39 Frequency setting current gain frequency Pr. 126
Terminal 4 frequency setting gain
frequency
Pr. 40 Start-time ground fault detection selection Pr. 249 Earth (ground) fault detection at start
Pr. 48 Output current detection level Pr. 150 Output current detection level
Pr. 49 Output current detection signal delay time Pr. 151 Output current detection signal delay time
Pr. 50 Zero current detection level Pr. 152 Zero current detection level
Pr. 51 Zero current detection time Pr. 153 Zero current detection time
Pr. 53 Frequency setting operation selection Pr. 161
Frequency setting/key lock operation
selection
Pr. 60 RL terminal function selection Pr. 180 RL terminal function selection
Pr. 61 RM terminal function selection Pr. 181 RM terminal function selection
Pr. 62 RH terminal function selection Pr. 182 RH terminal function selection
Pr. 63 STR terminal function selection Pr. 179 STR terminal function selection
Pr. 64 RUN terminal function selection Pr. 190 RUN terminal function selection
Pr. 65 A, B, C terminal function selection Pr. 192 A,B,C terminal function selection
Pr. 66 Retry selection Pr. 65 Retry selection
Pr. 70 Soft-PWM setting Pr. 240 Soft-PWM operation selection
Pr. 76 Cooling fan operation selection Pr. 244 Cooling fan operation selection
Pr. 80 Multi-speed setting (speed 8) Pr. 232 Multi-speed setting (speed 8)
Pr. 81 Multi-speed setting (speed 9) Pr. 233 Multi-speed setting (speed 9)
Pr. 82 Multi-speed setting (speed 10) Pr. 234 Multi-speed setting (speed 10)
Pr. 83 Multi-speed setting (speed 11) Pr. 235 Multi-speed setting (speed 11)
Pr. 84 Multi-speed setting (speed 12) Pr. 236 Multi-speed setting (speed 12)
Pr. 85 Multi-speed setting (speed 13) Pr. 237 Multi-speed setting (speed 13)
Pr. 86 Multi-speed setting (speed 14) Pr. 238 Multi-speed setting (speed 14)
Pr. 87 Multi-speed setting (speed 15) Pr. 239 Multi-speed setting (speed 15)
Pr. 88 PID action selection Pr. 128 PID action selection
Pr. 89 PID proportional band Pr. 129 PID proportional band
Pr. 90 PID integral time Pr. 130 PID integral time
Pr. 91 PID upper limit Pr. 131 PID upper limit
Pr. 92 PID lower limit Pr. 132 PID lower limit
Pr. 93 PID action set point for PU operation Pr. 133 PID action set point
Pr. 94 PID differential time Pr. 134 PID differential time
Pr. 95 Rated motor slip Pr. 245 Rated slip
Pr. 96 Slip compensation time constant Pr. 246 Slip compensation time constant
Pr. 97
Constant power range slip compensation
selection
Pr. 247
Constant-power range slip compensation
selection
H7(Pr. 559) Second electronic thermal O/L relay Pr. 51 Second electronic thermal O/L relay
b1(Pr. 560) Regenerative function selection Pr. 30 Regenerative function selection
b2(Pr. 561) Special regenerative brake duty Pr. 70 Special regenerative brake duty
n1(Pr. 331) Communication station number Pr. 117 PU communication station number
n2(Pr. 332) Communication speed Pr. 118 PU communication speed
n3(Pr. 333) Stop bit length Pr. 119 PU communication stop bit length
n4(Pr. 334) Parity check presence/absence Pr. 120 PU communication parity check
n5(Pr. 335) Number of communication retries Pr. 121 Number of PU communication retries
n6(Pr. 336) Communication check time interval Pr. 122 PU communication check time interval
n7(Pr. 337) Waiting time setting Pr. 123 PU communication waiting time setting
n11(Pr. 341) CR/LF setting Pr. 124 PU communication CR/LF selection
n16(Pr. 992) PU main display screen data selection Pr.52 DU/PU main display data selection
n17(Pr. 993) Disconnected PU detection/PU setting lock Pr. 75
Reset selection/disconnected PU
detection/PU stop selection
Control terminal block
Screw type terminal block
Fix a wire with a flathead screw
(Screw size: M2(M3 for terminal A, B, C))
Length of recommended blade terminal: 6mm
Spring clamp terminal block
Fix a wire with a pressure of inside spring
Length of recommended blade terminal: 10mm
(Blade terminal of FR-S500 is unavailable)
PU FR-PU04
FR-PU07
FR-PU04 (some functions, such as parameter copy, are
unavailable.)
Installation size
FR-D720-0.1K to 3.7K, FR-D740-0.4K to 3.7K, FR-D720S-0.1K to 1.5K, FR-D710W-0.1K to 0.75K are compatible in
mounting dimensions
Item FR-S500 FR-D700