EasyManuals Logo

Mitutoyo ID-SX User Manual

Mitutoyo ID-SX
4 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Printed in Japan
Mitutoyo Corporation 1-20-1 Sakado, Takatsu-ku, Kawasaki City, Kanagawa 213-8533
ABS Digimatic Indicator ID-SX
en
Contents
Cap
Battery holder
Display (LCD)
[ON/OFF] key
[ORIGIN] key
[in/mm] key (except for ID-S1012X,
ID-S112X, ID-S112PX)
[+ / -] key
Output connector (with cap)
Lifting lever mount (left and right)
Back with lug
Flat back
Release mounting hole (with rubber cap)
Stem
Spindle
Contact point
Rubber boot (dustproof type only)
Tips
Dimensions with an asterisk (*) are for the at back type. Dimensions without an asterisk (*) are
common for the back with lug type and the at back type.
■ Display (LCD)
Key icon operation
=
> 2 s
=
< 1 s
2.  Installing (Replacing) the Battery
NOTICE
Be sure to use SR44 (silver oxide button battery No. 938882) for the battery.
The product may display an error or malfunction if the battery holder is not mounted correctly.
If the product will be out of use for 3 months or more, remove the battery and store it
separately, to prevent damage to the product due to battery uid leakage.
Do not use a pointed object or excessive force to remove the battery holder. This may damage
the battery holder.
SR44
31 5
2 4
1
Use a athead screwdriver or similar to remove the battery holder.
2
If replacing an existing battery, remove the old battery.
3
Insert a new battery into the battery holder with the "+" symbol facing the display (LCD).
4
Attach the battery holder.
5
Press the [ORIGIN] key for 1 second or more.
Tips
If no value is displayed even when a battery is installed, reinstall the battery.
Although the display may show garbled text, [E] (minimum digits) or [------] just after installing
the battery, this is not abnormal. Perform reference point setting as is (refer to "5. ORIGIN
Setting (Reference Point Setting)").
Reference point settings are cleared when the battery is removed. Perform reference point
setting again after installing the battery.
Unit display
Measured value display
Sign display
Reverse count display
Battery voltage decrease
display
Safety Precautions
To ensure operator safety, use this product in conformance with the directions, functions
and specications given in this User's Manual.
Use under other conditions may compromise safety.
WARNING
Always keep batteries out of reach of children, and if swallowed, consult a physician im-
mediately.
Batteries should never be short-circuited, disassembled, deformed or come in contact with
extreme heat or flames.
If battery alkaline liquid comes in contact with the eyes, flush eyes immediately with clean
water and consult a physician. If battery alkaline liquid comes in contact with the skin,
flush the exposed area thoroughly with clean water.
CAUTION
Never attempt to charge the primary battery or reverse the positive-negative terminals
when mounting. Improper battery handling or mounting may cause the battery to explode,
cause battery leakage and/ or serious bodily injury or malfunctioning.
Always handle the sharp measuring faces of this product with care to avoid injury.
NOTICE
Do not disassemble or modify. This may cause damage.
Do not use or store the product in a place with sudden temperature changes. Adapt the
product to room temperature before use.
Do not store the product in a place with high humidity or a lot of dust. Also, avoid usage in
places exposed to splashes of water or coolant.
Do not apply excessive force or subject to sudden impacts such as dropping.
Be sure to perform reference point setting before measurement.
Remove dust, cutting chips, etc. before and after use.
Do not write numbers, etc. with an electric pen. This may cause damage.
Do not operate the keys with a pointed object (such as a screwdriver or ballpoint pen).
Avoid loads in the vertical direction relative to the spindle or usage involving torsion to the spindle.
This product is shipped without a battery. Install a battery before use.
The battery supplied is for conrming the functions and performance of the product. Note
that this battery may not fulll the expected life.
When disposing of batteries, follow local laws, regulations, etc.
Malfunction or damage due to depleted batteries, etc. is not covered by the warranty.
The dustproof type protects the spindle and bearing from dust, water, oil, etc. by attaching
a rubber boot, etc. to the standard type. Note that the dustproof type is not completely
waterproof. Do not immerse the product in liquid or use the product in a place where it is
intensively exposed to oil or water.
In environments with large temperature fluctuations, the measurement errors will increase
due to thermal expansion of parts and fixtures. Therefore use the product where the
temperature fluctuation is as little as possible.
When it is moved to a different temperature environment, allow sufficient time for the
product to thermally stabilize before use.
User's Manual No. 99MAH032A2
Date of publication: November 1, 2020
1.  Names and Dimensions of Components
NOTICE
The product display does not rotate. Forcibly rotating the display may damage the product.
■ ISO/JIS type
Back with lug type: ID-S1012X, -S1012MX, -S112X, -S112MX, -S112PX, -S112PMX
Flat back type*: ID-S1012XB, -S1012MXB, -S112XB, -S112MXB, -S112PXB, -S112PMXB
Unit: mm
Dustproof type
ø
6.5
M2.5x0.45
*
ø59
13.3
ø10.9
46.5
21.2
7.3
ø8
0
-0.009
7.6
54.4
50.1
20
5
16
17
19.9
ø54
ID-S112PX, ID-S112PXB,
ID-S112PMX, ID-S112PMXB
14
37.2
AGD type
Back with lug type: ID-S1012EX, -S112EX, -S112TX, -S112PEX
Flat back type*: ID-S1012EXB, -S112EXB, -S112TXB, -S112PEXB
Dustproof type
ø
1/4
Thread
No.4-48UNF
3/8
ø2.32
0.58
0.46
0.52
ø.43
1.97
0.3*
1/4
ø9.52 mm
1/4
2
1.74
0.79
0
-0.03
ø2.12
0.63
3/4
0.78
1.46
ID-S112PEX, ID-S112PEXB
Unit: in
This is the symbol of American Gage Design (AGD). It means that this type conforms to
appropriate dimensions of Dial Indicators in ASME/AGD 2 and has interchangeability.
1.
Names and Dimensions of Components ......1
2. Installing (Replacing) the Battery .......... 1
3. Setup ....................................................2
4. Power ON/OFF ..................................... 2
5. ORIGIN Setting ..................................... 2
(Reference Point Setting)
6. Measurement Method ........................... 3
7. Precautions after Use ........................... 3
8. Errors and Troubleshooting .................. 3
9. Rubber Boot Replacement .................. 3
(ID-S112PX, ID-S112PXB)
10. Output Function .................................... 3
11. Specications........................................ 4
12. Accessories (Optional).......................... 4
13. O󰀨-Site Repairs (Subject to Charge) .... 4

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Mitutoyo ID-SX and is the answer not in the manual?

Mitutoyo ID-SX Specifications

General IconGeneral
BrandMitutoyo
ModelID-SX
CategoryMeasuring Instruments
LanguageEnglish

Related product manuals