DOWNLOAD
https://nadelectronics.com/product/C-700-V2
https://support.nadelectronics.com
https://www.bluesound.com/downloads
NETWORK SETUP
Connect your C 700 V2 to your home network via Wired or Wireless connection.
A. WIRED CONNECTION
Using an Ethernet cable (not supplied), connect one end to C 700 V2’s LAN port and
the other end directly to your home network or router.
B. WIRELESS CONNECTION
Connect C 700 V2 to your wireless network using any of the following four methods.
1 Wireless Accessory Configuration (WAC) using iOS/iPadOS device
2 Using iOS/iPadOS device
3 Using Android device
4 Wireless manual setup
Condition: C 700 V2 must be at hot spot mode. C 700 V2 default setting is at hot spot
mode.
IMPORTANT!
• Hotspot mode will time out after 15 minutes. To re-establish hotspot mode, reboot
C 700 V2 or power it down and wait at least 5 seconds before powering it back up.
• The following procedures may change over time without notice. Always check the
C 700 V2 product page for the latest updates.
• The BluOS app for iOS and Android devices, as well as for Windows and macOS
desktops, can be downloaded from their respective application stores and also from
BluOS downloads at https://bluos.io/downloads.
1 WIRELESS ACCESSORY CONFIGURATION (WAC) USING iOS/iPadOS DEVICE
Wireless Accessory Configuration (WAC) setup mode is supported by iOS/iPadOS
application. At WAC setup mode, network name and password are not required for
the C 700 V2 to be connected to your network.
a Select Settings menu of your iOS/iPadOS device.
b Go to Wi-Fi and select the network you would like to use with your C 700 V2.
c Scroll down to SETUP NEW AIRPLAY SPEAKER. Select your C 700 V2 player
indicated by C 700 V2-xxxx where xxxx corresponds to the last 4 digits of the
Machine Access Control (MAC) address* of your C 700 V2.
d When AirPlay Setup screen comes up, select Next. Note that you can also
customize the name of your C 700 V2 by entering desired name in the line item
Speaker Name.
e Airplay Setup will proceed automatically. Follow setup process until Setup
Complete is shown. Select Done to exit setup mode.
2 USING iOS/iPadOS DEVICE
a Open BluOS App. Select Players icon in the bottom portion of the App.
b From upper right corner of the App, select
+ to launch Easy Setup Wizard.
c From My Players screen prompt, select your C 700 V2’s unique network ID* under
Needs Setup.
d When AirPlay Setup screen comes up, select Next. Note that you can also customize
the name of your C 700 V2 by entering desired name in the line item Speaker Name.
e Airplay Setup will proceed automatically. Follow setup process until Setup Complete is
shown. Select Done.
f C 700 V2 will automatically enter Looking for Upgrade mode. If a firmware upgrade is
available, it will be installed automatically. Once the upgrade is finished, select Finish to
exit setup mode.
* The C 700 V2’s unique network ID is listed as the product name (i.e., C 700 V2) immediately
followed by the last four digits in the MAC (Machine Access Control) address (example: C 700
V2-ACF7).
3 USING ANDROID DEVICE
a Select your C 700 V2’s unique network ID* from the Wi-Fi Setup connection settings
menu of your Android device and connect/join.
b Wait until Internet may not be available window appears. Select Connect only this
time.
c Open the BluOS App and wait for the New Player detected window to appear (this
may take some time). Select Setup now.
d Select your C 700 V2’s unique network ID* from My Players window.
e Select your Home Wi-Fi Network from Choose WiFi Network drop down menu.
i. If your Home Wi-Fi Network does not appear or is hidden, select Manual SSID Entry.
ii. Enter SSID name.
iii. Select the Network Security your network uses under Choose Security Method.
f Enter your home network’s Wi-Fi Password in the field provided and select Continue.
g Select or enter preferred Name to customize your C 700 V2 for easier identification in
the Player Drawer. Select Continue.
h Network setup process proceeds automatically. As it advances, it will automatically
enter Looking for Upgrade mode. If a firmware upgrade is available, it will be installed
automatically.
i Network setup process is completed when Setup Complete is shown in the App.
Select Finish to exit the setup process.
To Next Page
Loading...
