NEC NC1700L - Page 113

113
Appendix
Error Code Error message Description
990 LaserBDEepromFail Data check sum error in EEPROM on LD board.
992 LDMCULockUp LD uC is locked up.
993 54VError 54V is abnormal.
995 LDEepromFail Communication error with the EEPROM on LD board.
996 KEY Switch Off The laser unit laser administrator switch is off.
1000 Slave Comm Fail Failed to communicate with slave MCU.
1003 Slave Comm Ack Fail Slave fauls to execut the command.
1004 Slave Power Ready Fail Slave Power Ready error
1005 Slave No Notify Slave Power Notify error
1500 P3P3V SAT PGOOD Fail Error detected with 3.3V power supply for FSB
1501 P2P5V SAT PGOOD Fail Error detected with 2.5V power supply for FSB
1502 XVT PGOOD Fail Error detected with DDR power supply for FMT FPGA
1503 P2P5V X PGOOD Fail Error detected with 2.5V power supply for FMT FPGA
1504 P1P8V X PGOOD Fail Error detected with 1.8V power supply for FMT FPGA
1505 P1V X PGOOD Fail Error detected with 1V power supply for FMT FPGA
1506 FMT FPGA DONE Fail FMT FPGA Configuration Error
1509 EXGPIO IC602 Fail I2C Device Access Error
1510 EXGPIO IC603 Fail I2C Device Access Error
1511 EXGPIO IC604 Fail I2C Device Access Error
1512 EEPROM IC2800 Write Fail I2C Device Access Error
1513 EEPROM IC601 Read Fail I2C Device Access Error
1514 EEPROM IC601 Write Fail I2C Device Access Error
1515 EEPROM IC601 Write Fail(Verify) I2C Device Access Error
1538 EEPROM IC2800 Read Fail I2C Device Access Error
1550 EEPROM IC2800 Write Fail Verify I2C Device Access Error
2000 IntegrityFail Integrity error with the internal software code of the
projector.
* When this error has occurred, the projector will not
accept any external demands. Communication with
external devices will not be performed either.
2010 Incorrect power-off PowerOff was not performed correctly last time.
2100 Diffuser2 Wheel Stop Diffuser2 Wheel has stopped.
2101 Diffuser2 Wheel Stop Precaution Diffuser2 Wheel Stop Precaution
2110 OverTemp.LS_G1 Precaution Set inside temperature (LS_G1) is close to over
temperature.
2111 OverTemp.LS_G2 Precaution Set inside temperature (LS_G2) is close to over
temperature.
2112 OverTemp.LS_G3 Precaution Set inside temperature (LS_G3) is close to over
temperature.
2113 OverTemp.LS_G4 Precaution Set inside temperature (LS_G4) is close to over
temperature.
2114 OverTemp.LS_B Precaution Set inside temperature (LS_B) is close to over
temperature.
2115 OverTemp.LS_R Precaution Set inside temperature (LS_R) is close to over
temperature.
2120 OverTemp.LS_G1 Set inside temperature (LS_G1) is abnormal.
2121 OverTemp.LS_G2 Set inside temperature (LS_G2) is abnormal.
2122 OverTemp.LS_G3 Set inside temperature (LS_G3) is abnormal.
2123 OverTemp.LS_G4 Set inside temperature (LS_G4) is abnormal.
2124 OverTemp.LS_B Set inside temperature (LS_B) is abnormal.
2125 OverTemp.LS_R Set inside temperature (LS_R) is abnormal.
2130 SensorFail LS_G_Module1 Failed to read LS_G_Module1 sensor.
2131 SensorFail LS_G_Module2 Failed to read LS_G_Module2 sensor.
2132 SensorFail LS_G_Module3 Failed to read LS_G_Module3 sensor.
2133 SensorFail LS_G_Module4 Failed to read LS_G_Module4 sensor.