En-28
Reducing image retention
The brightness of the screen, the position of the picture,
positive/negative mode and screen wiper are adjusted to
reduce image retention.
Set “ADVANCED OSM” to “ON” in the FUNCTION menu.
On “PDP SAVER” of “FUNCTION” menu, select
“MANUAL”, then press the MENU/ENTER button.
The “PDP SAVER” screen appears.
Set “ADVANCED OSM” to “ON” in the FUNCTION menu.
On “PICTURE FREEZE” of “FUNCTION” menu, select
“BTM LEFT”.
SEL. ADJ. RETURN
EXIT
FUNCTION
ADVANCED OSM
POWER MGT.
INPUT SKIP
SUB. PICTURE
ZOOM NAV
PICTURE FREEZE
PDP SAVER
CLOSED CAPTION
CAPTION CONT.
PWR. ON MODE
: OFF
: OFF
: OFF
: BTM LEFT
: BTM LEFT
: MANUAL
: OFF
: LOW
Information
PICTURE FREEZE Function
* This feature does not function during multi screen mode.
* Digital zoom is not available while this function is
operating.
* A further press of the ACTIVE SELECT button while
this function is operating will cancel this function.
* Providing a 2-screen display will cancel this function.
PICTURE FREEZE settings
OFF: Will not show the still image.
S BY S1, 2: The still images captured by pressing the
ACTIVE SELECT button will be shown on the sub
screen of side-by-side mode.
BTM LEFT~TOP LEFT: The still images captured by
pressing the ACTIVE SELECT button will be shown
on the sub screen of picture-in-picture mode.
PEAK BRIGHT
Use this to activate the brightness limiter.
Example: Setting “PEAK BRIGHT” to “75%”
On “PEAK BRIGHT” of “PDP SAVER” menu, select “75%”.
SEL. ADJ. RETURN
EXIT
PDP SAVER
PEAK BRIGHT
ORBITER
INVERSE/WHITE
SCREEN WIPER
SOFT FOCUS
OSM ORBITER
OSM CONTRAST
: 75%
: AUTO1
: OFF
: OFF
: OFF
: ON
: LOW
Information
PEAK BRIGHT settings
100%: The brightness of the screen is adjusted
automatically to suit the picture quality.
75%, 50%, 25%: Sets maximum brightness.
The brightness level decreases in the order of 75%,
50%, 25%. 25% provides minimum brightness.
* These values are approximate.
SEL. ADJ. RETURN
PDP SAVER
PEAK BRIGHT
ORBITER
INVERSE/WHITE
SCREEN WIPER
SOFT FOCUS
OSM ORBITER
OSM CONTRAST
: 100%
: AUTO1
: OFF
: OFF
: OFF
: ON
: LOW
EXIT
Information
When set to AUTO
Set automatically, as described below.
PEAK BRIGHT: 100%
ORBITER: AUTO1 or AUTO2
INVERSE/WHITE: OFF
SCREEN WIPER: OFF
SOFT FOCUS: OFF
OSM ORBITER: ON
OSM CONTRAST: LOW
RGB/PC
RGB/PC
RGB/PC
RGB/PC
RGB/PC
RGB/PC
Side-by-Side Picture-in-Picture
ACTIVE
SELECT
button
ACTIVE
SELECT
button
S BY S1
RGB/PC
RGB/PC
or
S BY S2
ORBITER
Use this to set the picture shift.
Example: Setting “ORBITER” to “AUTO2”
On “ORBITER” of “PDP SAVER” menu, select “AUTO2”.
SEL. ADJ. RETURN
EXIT
PDP SAVER
PEAK BRIGHT
ORBITER
INVERSE/WHITE
SCREEN WIPER
SOFT FOCUS
OSM ORBITER
OSM CONTRAST
: 100%
: AUTO2
: OFF
: OFF
: OFF
: ON
: LOW
Information
ORBITER settings
OFF: Orbiter mode does not function.
This is the default setting when RGB is input.
AUTO1: The picture moves around the screen
intermittently, making the picture smaller. This is the
default setting when a Video or a DVD/HD signal is
input. Set to “OFF” when these signals are not used.
AUTO2: The picture moves around the screen
To Next Page
Loading...
Need help?
General