Netum NT-1200 User Manual

NT-1200
Quick Setup Guide
This is a plug and play model if you use a US keyboard. If you use other type of keyboard, plug the
USB cable on your device , setup keyboard language before you use it. (refer to below Keyboard
Language Type) after that the scanner can start to work.
If you want to do other configurations please refer to below programming barcodes.
Barcode Programming
Netum barcode scanners are factory programmed for common terminal and communications
settings. If you need to change these settings, programming is accomplished by scanning the bar
codes in this guide. An asterisk (*) next to an option indicates the default setting.
Firmware Version
Read below command barcode to check scanner firmware version.
000A0
Firmware Version
Please advise the scanner model number and firmware version when you have any inquiry about
the scanner.

Netum NT-1200 Specifications

General

Interface	USB
Dimensions	170mm x 70mm x 95mm
Weight	150g
Scanning Technology	Laser
Type	Handheld Barcode Scanner
Operating System Compatibility	Windows, Linux, Mac
Scan Mode	Manual
Operating Voltage	DC 5V

Summary

Quick Setup Guide

Barcode Programming

Configure scanner settings by scanning barcodes. Default settings are indicated by an asterisk.

Firmware Version Check

Instructions to check the scanner's firmware version using a specific command barcode.

Keyboard Language Setup

Keyboard Layout Options

Set scanner to recognize specific keyboard layouts like US, French, German, Spanish, Portugal, Turkey, and Italy.

Scanning Modes Configuration

Key Holding Scanning Mode

Trigger reading by pressing the button; release to end. Reading ends on success or timeout.

Continuous Scanning Mode

Scanner performs continuous work. Reading ends on success or timeout.

Terminator Configuration

Suffix Terminator Settings

Configure scanner to add terminating characters like CR, LF, or CR+LF to scanned data.

Reader Beep Tone Control

Beep Tone On/Off Settings

Barcodes to enable or disable the scanner's beep tone feedback.

Default Configuration Settings

Factory Reset Procedure

Scan barcode to restore all scanner configurations to factory defaults.

Common Function Barcodes

EAN-8 Barcode Enable/Disable

Options to enable or disable EAN-8 barcode scanning.

Transmit Check Digit Settings

EAN-8 & EAN-13 Check Digit Control

Control transmission of check digits for EAN-8 and EAN-13 for data integrity.

Add-On Code Configuration

EAN-8/EAN-13 Add-On Code Support

Configure scanner to read two-digit or five-digit add-on codes for EAN-8/EAN-13.

EAN-13 Barcode Management

EAN-13 Barcode Enable/Disable

Barcodes to enable or disable EAN-13 barcode scanning.

Barcode Type Enable/Disable

Codabar, Code 11, Code 39 Settings

Barcodes to enable or disable Codabar, Code 11, and Code 39 barcode scanning.

Add-On Code Visualization

EAN-8/EAN-13 Add-On Code Examples

Visual examples of EAN-8/EAN-13 barcodes with add-on codes highlighted.

Advanced Barcode Symbologies

ASCII, Code 93, Code 128 Settings

Barcodes to enable or disable Full ASCII, Code 93, and Code 128 barcode scanning.

GS1 DataBar Barcode Support

Barcodes to enable or disable GS1 DataBar Limited and Omnidirectional scanning.

UPC-A Barcode Configuration

UPC-A Enable/Disable Options

Barcodes to enable or disable UPC-A barcode scanning.

UPC-A Transmit Check Digit Control

Control transmission of UPC-A check digit for data integrity.

UPC-A Add-On Code Support

Configure scanner to read two-digit or five-digit add-on codes for UPC-A.

UPC-A and UPC-E Barcode Management

UPC-A Transfer to EAN-13 Settings

Barcodes to enable or disable UPC-A to EAN-13 transfer.

UPC-E Barcode Enable/Disable

Barcodes to enable or disable UPC-E barcode scanning.

Interleaved 2 of 5 Barcode Settings

Interleaved 2 of 5 Enable/Disable

Barcodes to enable or disable Interleaved 2 of 5 barcode scanning.

2 of 5 Barcode Variants Configuration

Industrial, Standard, Matrix 2 of 5 Settings

Barcodes to enable/disable Industrial, Standard, and Matrix 2 of 5 barcode scanning.

MSI Barcode Configuration

MSI Barcode Enable/Disable

Barcodes to enable or disable MSI barcode scanning.

Plessey Barcode Configuration

Plessey Barcode Enable/Disable

Barcodes to enable or disable Plessey barcode scanning.

UPC/EAN/JAN Add-On Code Options

Add-On Code Type Configuration

Configure scanner for 2-digit, 5-digit, or combined 2&5 digit add-on codes for UPC/EAN/JAN.

Code ID Setting Configuration

Code ID Prefix/Suffix Identification

Configure scanner to recognize barcode types using Code ID prefixes or suffixes.

Custom Prefix and Suffix Setup

Custom Prefix Configuration

Steps to scan codes to add a custom prefix to scanned data, clearing previous settings.

Custom Suffix Configuration

Steps to scan codes to add a custom suffix to scanned data, clearing previous settings.

Clear Prefix/Suffix Settings

Barcodes to clear existing custom prefix and suffix configurations.