Netum NT-1228BC User Manual

NT-1228BC V18.7.12
Quick Setup Guide
This model can work both via USB cable or via bluetooth.
Connection Mode
Working via USB cable
Get Started: Connect scanner with your device via USB cable. If you use US keyboard, it's a plug and play
model. If you use other type of keyboard , please refer to below "keyboard language type" to set the
keyboard language before use it.
Working via Bluetooth
Get Started: After you connect the bluetooth with your device (please refer to the section of "bluetooth
connection" from this manual) then you can start to use it. (US keyboard by default) If you use other type of
keyboard , please refer to below "keyboard language type" to set the keyboard language before use it.
Low voltage Alarm: Scanner will make 2x beeps to remind you that it's under low voltage. Plug the USB cable
to charge power for it.
If you want to have other configurations please refer to below programming barcodes.
Firmware Version:
Read below command barcode to check scanner firmware version.
Check Scanner Version
Below programming barcodes are applied for version ≥ NT_ZNCWBSDk8815
Barcode Programming
Netum barcode scanners are factory programmed for the most common terminal and communications
settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this
guide. An asterisk (*) next to an option indicates the default setting.

Netum NT-1228BC Specifications

General

Brand	Netum
Model	NT-1228BC
Category	Barcode Reader
Language	English

Summary

Quick Setup Guide

Connection Modes

Details on connecting the scanner via USB or Bluetooth.

Operational Features

Includes low voltage alarm, firmware version check, and barcode programming.

Bluetooth Pairing Procedures

Windows Pairing

Step-by-step guide to pair the scanner with Windows devices.

Android Pairing

Instructions for connecting the scanner to Android devices via Bluetooth.

iOS Pairing, BT HID Mode, and Keyboard Language

iOS Device Pairing

How to connect the scanner to iOS devices via Bluetooth.

BT HID Mode (Default)

Scanner functions as a keyboard without software installation.

Keyboard Language Setup

How to set the keyboard language for correct code scanning.

Advanced Operation Modes

Scan Mode Configuration

Trigger, Continuous, and Auto Sense Modes

Settings for manual trigger, continuous, and auto-sense scanning.

Working Mode Functionality

Instructions for using offline mode and managing scanned data.

Terminator and Idle Time Settings

Terminator Configuration

Settings for the terminating character suffix (CR, CRLF, TAB).

Additional Device Settings

Factory Default Restore

Procedure to restore the scanner to its factory default settings.

1D Barcode Reading Modes

UPC/EAN Enable/Disable

Options to enable or disable UPC-A, UPC-E, EAN-8, and EAN-13.

UPC/EAN Configuration

UPC/EAN Enable/Disable Continued

Further settings to enable or disable UPC and EAN barcode types.

UPC/EAN Supplemental and Check Digit Settings

UPC/EAN Supplemental Decoding

Options for decoding UPC/EAN barcodes with supplements.

Code 128 and GS1-128 Configuration

Enable/Disable Code 128

Options to enable or disable Code 128 barcode scanning.

Enable/Disable GS1-128

Options to enable or disable GS1-128 barcode scanning.

ISBT 128, Code 39, and Check Digit Settings

Enable/Disable ISBT 128

Options to enable or disable ISBT 128 barcode scanning.

Code 39 Configuration

Settings for Code 39, including check digit verification.

Code 39 Transmission and ASCII Settings

Code 93 Configuration

Settings for enabling or disabling Code 93 barcode scanning.

Code 93 and Code 11 Settings

Enable/Disable Code 11

Code 11 Configuration and Check Digit Verification

Code 11 Check Digit Verification

Interleaved 2 of 5 and I 2 of 5 to EAN-13 Conversion

Enable/Disable Interleaved 2 of 5

Discrete 2 of 5, Matrix 25, and Standard 25 Settings

Enable/Disable Discrete 2 of 5

Enable/Disable Matrix 25

Enable/Disable Standard 25

Standard 25 Configuration and Codabar Settings

Standard 25 Check Digit Verification

Codabar Enable/Disable

MSI and GS1 DataBar Configuration

Enable/Disable MSI

Enable/Disable GS1 DataBar-14

GS1 DataBar Limited/Expanded and PDF417 Settings

Enable/Disable GS1 DataBar Limited

Enable/Disable GS1 DataBar Expanded

PDF417 Configuration

PDF417 and QR Code Settings

QR Code Configuration

QR Code, Data Matrix, and Phase Reading Settings

QRCode Enable/Disable

Data Matrix (DM) Configuration

Maxi Code and Aztec Code Settings

Enable/Disable Maxi Code

Enable/Disable Aztec Code

Han Xin Code and Barcode Character Hiding

Han Xin Code Configuration

Output Format and Barcode Character Hiding

Output Format Settings

Custom Prefix and Suffix Configuration

Add Prefix or Suffix

Procedure for adding custom prefixes and suffixes to scanned data.

Output Format and Prefix/Suffix Examples

Output Format Options

Example: Add Normal Prefix/Suffix

Demonstrates adding 'A','B' as prefixes and '!' as suffix.

Prefix and Suffix Configuration Examples

Example: Add Normal Prefix and Suffix

Step-by-step guide for adding normal prefix and suffix.

Example: Add Suffix for '!'

Example of adding '!' as a suffix using specific barcodes.

Combination Key Suffix Example

Example: Add "Ctrl+P" Suffix

Demonstrates adding "Ctrl+P" as a suffix using specific barcodes.