Nexo NXAMP4X1

To Next Page

To Previous Page

MENU DESCRIPTION

Miscellaneous options

This menu will allow tweaking different small options available in the NXAMP4x1 Powered

TDcontroller. This menu is not yet implemented in LOAD2_48.

PAGE 46 OF 80

Main Page

Table of Content6
- Table of Contents6
- Dsp Core10
- Integrated Amplifier10
- Level and Latency10
Nxamp4X1 Versus Nx242: What's New10
- Software10
- What' Changed?10
What's Remaining the same10
- Computing Resources11
- Ethersound™ Optional Board11
- Four Separate Inputs11
- Power Supply11
- User Interface11
- Amplifier Indicators12
What's Changed10
Quick Start12
- Encoder13
- Lcd Display13
- Mute Buttons13
- Navigation Buttons (a & B)13
- Select Buttons13
- Volume Indicators13
- Air Intakes14
- Channel Indicators14
- Screw Holes for Handles14
Front Panel Description12
- Power Switch12
Back Panel Description15
- Balanced Audio Inputs with Link15
- Expansion Slot15
- Gpio Port15
- Mains Connectors15
- Power Outputs15
- Rs-232 Port15
Basic Functions16
- Rear End Mounting Holes16
- Reset16
- Select Your Cabinet Set-Up16
- Selecting Cabinet Family16
- Auto Save17
- Back to Default17
- Enter the Download Mode17
- Using the Amplifier Without the Tdcontroller Functionality17
What's Inside the Carton Box18
Setting-Up Advice19
Earth Connection19
Mains Setting19
Mounting the Nxamp4X1 in a Rack (Grounding, Shielding & Safety Issues)19
Using the Nxamp4X1 Without a Rack21
Fuses21
Electromagnetic Environments21
Analogue Input Signal Cables21
Nxamp4X1 Power Outputs Wiring23
General Description24
Global Architecture24
- Power Supply Block24
- Analog Input Block25
- Control Block25
- Power Amplifier Blocks26
- Power Outputs Block26
- Communication Block27
- User Interface Block27
- Expansion Slot Block29
Block Diagram Description30
Patching and Routing (1)31
- Subsonic and Vhf Filtering (3)31
- User Set-Up Delay31
- Crossover Section (6)32
- Equalising Single Component Response and Nxstream Processing (5)32
- Equalising Wideband Acoustical Response (3)32
- Gain Section (29)32
- Post Protection Eq and Low Pass (27) (28)32
- User Set - up , Array Eq (4)32
- Displacement Control (7) (8) (9)33
- Mechanical Stress Control (10) (11)33
Delay & Polarity Inversion (2)31
Equalisation & Filtering31
- Factory Set-Up Delay31
Protections33
- Source Signals for Protection Algorithms (25)33
- Global Purpose Vceq (14)34
- Hf Acceleration Control (13)34
- Hf Displacement Control (12)34
- Loudspeaker Peak Limiters (15)34
- Temperature Control (16) (17)34
- Amplifier Integrate Current Limiter (21)35
- Amplifier Peak Current Limiter (20)35
- Amplifier Peak Voltage Limiter (22)35
- Amplifier Short Circuit Detector (24)35
- Interchannel Regulation (19)35
Menu Description36
Changing Cabinet Family36
Adjusting Volume37
Adjusting Delay38
Adjusting Gain39
- Option Menu40
Adjusting Array Eq39
Options Menu40
- System Config40
- Input Patch41
- Save/Recall User Setups43
- Gpio Mode45
- Security45
- Miscellaneous Options46
- About « Loudspeaker Management Devices47
Installation Recommendations47
- Operating Sub's Fed through an Aux Output47
- Operation of Multiple Powered Tdcontrollers47
Audio Chain Recommendations47
System Alignment47
- Geometrical Alignment48
- Measuring and Aligning Phase in the Overlapping Region48
- Ethersound ™ in Port50
- Ethersound ™ Network Status Led S50
Nxes104 Expansion Board and Remote Control50
Nxes104 Physical Description50
- Ethersound out Port51
- Mono-Directional, Non ES100 Devices51
- Remote Es100 Port51
Various Ethersound™ Devices Description51
- Bi-Directional, Non ES100 Devices52
- Es100 Devices52
- Es100/Spkr Devices52
Ethernet Additional Hardware52
- Hubs52
- Ethernet Cables53
- Switches53
- Wireless Lan53
- Fiber Optic55
Installation Inside the Nxamp4X156
NXAMP Control Page in Esmonitor Software56
- Delay Unit57
- Input Meters57
- Input Meters Choice57
- Arrayeq Settings58
- Delay Settings58
- Gain Control58
- Input Patch58
- Mute Button58
- Output Meters58
- Security58
- Volume Control58
- Virtual Front Panel59
Nxwin4 Software for Nxamp4X1 Firmware Upgrade60
- Serial Port Upgrade60
What You Need to Upgrade Your Nxamp4X160
Connect the Computer to the Nxamp4X161
- Ethersound™ in Port61
- Ethersound™ Upgrade61
- Remote Es100 Port61
- Rs-232 Serial Port61
Using the Nxwin4 Software61
- Begin the Upgrade63
- In Download Mode63
- Choosing a Cabinet Setup64
- Select Your Cabinet Set-Up64
- Selecting Cabinet Family64
Using the Controller after a Firmware Update64
Technical Specifications65
Thermal Dissipation and Current Drawn66
Dimensions66
Application Note: Driving the Sub from the Aux Send67
- Consequences of Badly Aligned Systems67
- What Is the Phase Relation between the Aux and Main Output of Your Desk67
- Why It Is Unlikely the Aux and Main Have the same Phase67
- Precautions & Check68
Appendix A : List of Supported Presets (Load2_48)70

Table of Contents

Other manuals for Nexo NXAMP4X1

Related product manuals