ENGLISH – 3
• After installing the opener, the door must reverse
when it contacts a 38-mm (1-1/2-inch) high object
(or a 2 by 4 board laid at) on the oor.
• For products having a manual release, instruct the
end user on the operation of the manual release.
• Only enable [+] feature when installed with a sec-
tional door.”, where + is the unattended operation
function.
• This operator not equipped for permanent wiring.
Contact licensed electrician to install a suitable re-
ceptacle if one is not available.
• Before commencing the installation, check the “Product
technical specications”, in particular whether this prod-
uct is suitable for automating your guided part. Should
it not be suitable, do NOT proceed with the installation.
• The product cannot be used before it has been com-
missioned as specied in the “Testing and commission-
ing” chapter.
• Before proceeding with the product’s installation, check
that all the materials are in good working order and suit-
ed to the intended applications.
• ATTENTION! In order to avoid any danger from
inadvertent resetting of the thermal cut-off de-
vice, this appliance must not be powered through
an external switching device, such as a timer, or
connected to a supply that is regularly powered or
switched off by the circuit.
• The system’s power supply network must include a dis-
connection device (not supplied) with a contact opening
gap permitting complete disconnection under the con-
ditions envisaged by Overvoltage Category III.
• Handle the product with care during installation, taking
care to avoid crushing, denting or dropping it, or allow-
ing contact with liquids of any kind. Keep the product
away from sources of heat and naked ames. Failure
to observe the above can damage the product, and
increase the risk of danger or malfunction. Should this
happen, stop installation immediately and contact Cus-
tomer Service.
• The manufacturer declines all liability for damages to
property, objects or people resulting from failure to ob-
serve the assembly instructions. In such cases, the war-
ranty for material defects shall not apply.
• The weighted sound pressure level of the emission A is
lower than 70 dB(A).
• Before working on the system (maintenance, cleaning),
always disconnect the product from the mains power
supply.
• Inspect the system frequently, in particular the cables,
springs and supports to detect any imbalances and
signs of wear or damage. Do not use the product if it
needs to be repaired or adjusted, because defective in-
stallation or incorrect balancing of the automation can
lead to injuries.
• The packing materials of the product must be disposed
of in compliance with local regulations.
• The product must not be installed outdoors.
• Prior to installing the drive motor, check that the door
is in good working order, correctly balanced and that it
opens and closes properly.
• Prior to installing the motor, remove all unnecessary ca-
bles or chains and deactivate any equipment – such as
locking devices – not required for motorised operation.
• Check that there are no points where people could get
trapped or crushed against xed parts when the door
is fully open or closed; if there are, arrange adequate
protective measures for these parts.
• After installation, make sure that the motor prevents or
stops opening of the door when the latter is loaded with
a 20-kg weight secured to the centre of its bottom edge
(for drive motors that can be used with doors having
opening widths exceeding 50 mm).
• After installation, make sure that the mechanism is prop-
erly adjusted and that the motor reverses when the door
collides with a 38mm (1inch 1/2) -tall object placed on
the ground (for drive motors incorporating a trapping
safety system that intervenes when the bottom edge of
the door encounters an obstacle).
• Following installation, check and ensure that no door
parts obstruct public roadways or pavements.
1.2 IMPORTANT SAFETY INSTRUCTIONS
a
WARNING – To reduce the risk of severe
injury or death:
• READ AND FOLLOW ALL INSTRUCTIONS.
• Never let children operate or play with door con-
trols. Keep the remote control away from children.
• Always keep the moving door in sight and away
from people and objects until it is completely
closed. NO ONE SHOULD CROSS THE PATH OF
THE MOVING DOOR.
• For vertically moving doors: NEVER GO UNDER A
STOPPED, PARTIALLY OPEN DOOR.
• For horizontally moving doors: NEVER GO
THROUGH A STOPPED, PARTIALLY OPEN DOOR.
• Test door opener monthly. The garage door MUST
reverse on contact with a 38-mm (1-1/2-inch) high
object (or a 2 by 4 board laid at) on the oor. Af-
ter adjusting either the force or thelimit of travel,
retest the door opener. Failure to adjust the open-
er properly increases the risk ofsevere injury or
death.
To Next Page
Loading...
Need help?
General
