What to do if Nidec DC Drives show EEPROM error?
If your Nidec DC Drives are showing an EEPROM error: 1. Recover factory defaults if function code parameter writing error. 2. Ask for service from supplier, if EEPROM damaged.
What causes over current in Nidec NE200-2S0015GB DC Drives during acceleration and how to fix it?
Overcurrent during acceleration in Nidec DC Drives can stem from a few reasons. If the acceleration time is too short, increase it. Also, check the input power source for low voltage. Finally, if the drive power rating is too small, choose a drive with higher capacity.
What causes over current at constant-speed in Nidec DC Drives?
If you're experiencing overcurrent at a constant speed with your Nidec DC Drives, several factors could be the cause. Check the load for any abnormal mutations. Also, verify the input power source isn't experiencing low voltage. Ensure your drive has sufficient power capacity. Finally, if you're using closed-loop vector control, inspect the encoder and its wiring for any sudden disconnections.
What to do if Nidec DC Drives show drive overload?
If your Nidec DC Drives are showing a drive overload, first check the input power source for low voltage. If the load is too heavy, select a drive with a bigger capacity. If the acceleration is too fast, increase the acceleration time. Also, avoid restarting the motor while it's still turning.
What causes over current in Nidec NE200-2S0015GB during deceleration?
Overcurrent during deceleration in Nidec DC Drives can occur due to several reasons. If the deceleration time is too short, increase it. If there is a large load inertia, add suitable brake devices. Finally, if the drive power rating is too small, choose a higher capacity drive.
What to do if Nidec NE200-2S0015GB DC Drives show keypad & control board communication interrupted?
If communication between the keypad and control board is interrupted on your Nidec DC Drives, check the connection cable between the keypad and control panel.
What to do if Nidec NE200-2S0015GB show external terminal fault?
If your Nidec DC Drives are showing an external terminal fault, check the external input, as the fault likely originates from the external control circuit.
What to do if Nidec NE200-2S0015GB show Parameter copy Error?
If your Nidec DC Drives are showing a Parameter copy Error: 1. Shorten the cable between Keypad and control board to reduce interference if too long connection cable between keypad and control board leads to interference in parameters transmission. 2. Before downloading, make sure the parameters match the drive, if the downloading parameters do not match the existed parameters in the drive.
What to do if Nidec DC Drives show ground fault?
If your Nidec DC Drives are indicating a ground fault, it could be due to a short circuit in one of the output phases. Check whether the electric motor insulation is weakening. Also, check whether the wiring between the frequency converter and the electric motor is damaged.
What to do if Nidec NE200-2S0015GB show fast current limit fault?
If your Nidec DC Drives are showing a fast current limit fault, it could be due to a load that is too large or a motor blocked to stall, so decrease the load and check the motor and mechanical part status. If the drive power rating is too small, choose a higher power drive. If the drive output circuit loop is grounded or short-circuited, remove the external fault.
Comprehensive technical specifications for NE200 and NE300 drives, covering control modes and features.
Diagram and explanation for connecting the drive and peripheral devices.
Details the terminal configuration for the main circuit wiring.
Important notes and precautions for main circuit wiring procedures.
Wiring diagrams and instructions for the control terminals.
Description of the drive's keypad, including button functions and indicators.
Instructions on how to view and modify function codes and parameters.
Parameters related to the drive's start and stop control modes.
Parameters specific to vector control mode operations.
Parameters for Voltage/Frequency (V/F) control methods.
Configuration parameters for matching the drive to the motor characteristics.
Settings for configuring the functions of digital and analog input terminals.
Configuration settings for the drive's output terminals.
Parameters for drive protection and fault handling.
Parameters related to the drive's operation interface and display.
Parameters for setting user passwords and write-in protection.
Lists common faults, possible causes, and corresponding solutions for troubleshooting.
Provides general guidance for diagnosing and resolving common drive abnormalities.
Guidelines for regular maintenance tasks to ensure drive longevity.
To Next Page
General