Configuring the Camera’s Wireless Settings
30
3 Choose the desired SSID (A 9) and press the k
button.
Up to ten SSIDs, with network profiles configured with the
camera and those detected by the camera, are listed.
If connection by any wireless device is not allowed with an access
point and the desired SSID (up to 32 alphanumerical characters)
is not detected, select New and press the k button. Enter a
network name (SSID) in the SSID screen. If using the six-month
complimentary T-Mobile HotSpot subscription, do not enter tmobile as a new network name
(SSID) (in the United States only).
For information on entering text, see “Entering Text with the Camera” (A 27).
Choose an SSID with a network profile and press the k button. Profile settings can be edited
by following the same procedure used for SSIDs for which network profiles have not been
configured. To delete an existing SSID profile, select the SSID and press the l button. If using
the six-month complimentary T-Mobile HotSpot subscription, do not edit or delete the
tmobile SSID (in the United States only).
Up to ten wireless LAN network profiles can be stored in the camera. If ten profiles have already
been configured and you would like to add a new one, first use the camera or the Utility to
delete an existing network profile from the camera.
C SSID Selection Screen
SSIDs with network profiles are listed first regardless of signal strength.
The icon to the left of each SSID indicates signal strength and is
displayed in red when out of range (A 52, 53).
The icon to the right of each SSID shows the status of the camera’s
network profiles:
B (home wireless LAN profile configured)
A (public wireless LAN profile configured)
See “Public Wireless LAN” (A iv) for more information on countries
in which public wireless LANs can be accessed by, and the wireless service providers that support
connection of, this camera.
-- (no profile configured)
If the full network name cannot be displayed, highlight the SSID and press the g (j) button to
display the full name. Press the g (j) button again to return to the select SSID screen.
Select SSID
AP1
New
AP2
AP3
AP4
Back
Select SSID
AP1
New
AP2
AP4
AP3
Back
Q7115_Wireless_EN.book Page 30 Tuesday, June 3, 2008 7:34 PM
Configuring the Camera’s Wireless Settings
31
4 Choose the network type and press the k button.
If connecting via a home wireless LAN, choose Home wireless
LAN.
If connecting via a public wireless LAN, choose Public wireless
LAN. See “Public Wireless LAN” (A iv) for more information on
countries in which public wireless LANs can be accessed by, and
the wireless service providers that support connection of, this
camera.
5 Choose the desired authentication method (A 9)
and press the
k button.
When Open system is selected, choose None or WEP in the
encryption screen and press the k button.
• When None is selected, proceed to step 7 if Home wireless
LAN was selected in step 4, or proceed to step 8 if Public
wireless LAN was selected in step 4.
• When WEP is selected, proceed to step 6.
6 Enter the encryption key (A 9).
The encryption key entry screen will vary depending upon the
selected authentication method.
• If Open system was set to WEP, or Shared key was
selected, enter the WEP key in the WEP key screen.
• If WPA-PSK or WPA2-PSK was selected, choose TKIP or AES
in the encryption screen and enter the TKIP or AES key.
For information on entering text, see “Entering Text with the Camera” (A 27).
If Home wireless LAN was selected in step 4, proceed to step 7, or proceed to step 8 if Public
wireless LAN was selected.
Network type
Home wireless LAN
Public wireless LAN
Authentication
Shared key
Open system
WPA-PSK
WPA2-PSK
Encryption
None
WEP
2610
1ABCD 23412
ABCDEFGH I J KL
N
M
OPQRSTUVWXY
0
Z
1 2 3456789
@
.
WEP key
Back Delete
Q7115_Wireless_EN.book Page 31 Tuesday, June 3, 2008 7:34 PM
To Next Page
Loading...
